Hi-ltte Rambo 230 Manuale d'uso - Pagina 6

Sfoglia online o scarica il pdf Manuale d'uso per Apparecchio di illuminazione Hi-ltte Rambo 230. Hi-ltte Rambo 230 9. 7r 230w moving head beam

Stampa la pagina

1. Menu Operation

INSTALLATION

Note: Lights be placed vertically upward,the shortest distance between working

lights must be more than or equal 900mm, lighting installation layout as following

900mm

5.3

Data cable

Data cable is DMX512 signal

Note: Signal line connections is X-type connector。

X-type connector-----If the external flexible cable or cord of

thislight is damaged, please replace professional cable or cord

from the manufacture or its agent.Lights' DMX input and output

connects to a three-pin

XLR and five-pin XLR insert, first pin is

grounded, then negative signal is

second pin, third pin

connects to the positive

polarity signal, fourth and

fifth are empty.In order to prevent

reception reflection and

3XLR plug

Terminal plug connect with XLR

interference control signal,

1.Grounding

plug second or third by a 0.25w

2.Signal-

120ohm resistor, then connect

3.Signal+

the resistor into last light's DMX

a terminal plug must be installed on

output jack

the first branch of the connected

device last 3-pin output jack.

controller is connects to the nearest input XLR 3-pin, then from the output of

the device connects to the input of the next device, continuous connection

one by one, the final output data cable terminal equipment plug one end

into the terminal.

If the signal transmission is long-distance , 512 signal amplifier must be

added. DMX512 signal controller connect to the input of the amplifier first,

then connect to the fixture from its output, couple with the terminal plug last.

1 Do not use two separate output connection, if connec t the

branch separating consecutive DMX512 signal amplifier must

be used to separate.

2 Please use the shielded twisted-pair cable, standard

microphone cable can not be reliably controlled long-

distance data.

6.Fuse Size

Power :100-240v

Fuse: 8A 6 * 30 main fuse

6.2 Power Connection

If the external flexible cable or cord of this light is damaged, the line is

up to the manufacturer or its service agent or a similar qualified person

to replace, in order to avoid danger. Connect the power supply

personnel must have the appropriate qualifications before proceeding,

you must make sure you are using the power supply voltage matches

the voltage identified and have overload or leakage protection. Directly

connect the device to the power supply, do not connect to the silicon

box dimming system, otherwise damage to the equipment.

Note:

1 Do not install other similar bulbs, otherwise it will produce safety hazards

or equipment damage.

2.To reduce the risk of damage to the light, replacing the lampbefore its life is

over 3.Mustn't use the banned scratched and damaged bulb

7.2 Changing lamp

1 Disconnect the power, so that the lamp cooling, the arm of the lamp

body lock locked in a horizontal position.

2 split bulbs:Remove thecover which is written "split this cover to replace

the lamp head cover"

3 Use a Phillips screwdriver to remove the fan two thumbscrews fixed

side.

4 with the appropriate force to push down the bulb when the lamp cup

beyond the edge of the

stainless steel shrapnel, taking up the lamp.

5 Install the bulb is the opposite of the operation.

AC POWER

Fan side

screws

Note: when replacing a lightlamp does not touch the bulb with bare

hands at the ball, avoiding oil stained hands on the ball. 2 When

you install and dismantle the lamp into the lamp gently

put on, can not let the bulb hit hard objects around it to prevent

damage the bulbs.

7.3 Correction bulbs

(lamp has been corrected before selling,

if the individual case happens when

changing the lamp, could following this

way. the light is reseted by turning on

the power,using the menu or console

light bulb to play a bunch of white beam.

2 Using Phillips screwdriver to open

the light body one bonnet side which is

printed "this cover to replace the lamp"

3 Using a flathead screwdriver to

adjust the lamp bracket adjustment

screw, turn the screw clockwise or

counter clockwise, and the lamp can

be right or left to adjust.