Dynabrade 13520 Sicurezza, funzionamento e manutenzione - Pagina 5

Sfoglia online o scarica il pdf Sicurezza, funzionamento e manutenzione per Utensile elettrico Dynabrade 13520. Dynabrade 13520 9. 1 hp dynastraight 6" extension, governor controlled, 1,800/3,400/4,500/6,000 rpm with 5/8" or 1" combination arbor/with 1/2" diameter arbor, with 5/8"-11 threaded arbor

Stampa la pagina

Dynabrade 13520 Sicurezza, funzionamento e manutenzione

mportant: A Preventative Maintenance Program is recommended whenever portable power tools are used.

• Use only genuine Dynabrade replacement parts to insure quality. To order replacement parts, specify Model#, Serial# and RPM of your air tool.

• It is strongly recommended that all Dynabrade rotary vane air tools be used with a Filter-Regulator-Lubricator to minimize the possibility of misuse due

to unclean air, wet air or insufficient lubrication. Dynabrade recommends the following: 10681 Air Filter-Regulator-Lubricator (FRL) – Provides accurate

air pressure regulation and two stage filtration of water contaminates.

• Dynabrade recommends one drop of air lube per minute for each 20 SCFM (example: if the tool specification states 40 SCFM, set the drip rate on the

filter-lubricator to 2 drops per minute). Dynabrade Air Lube (P/N 95842: 1 pt 473 ml) is recommended.

• Grease the planetary gear assembly with 95542 Grease by applying 2-3 Plunges with 95541 Grease Gun every 50 of use, to achieve

maximum gear life.

Routine Preventative Maintenance: Check free speed of Extension Dynastraight using a tachometer. This governor controlled grinder should be speed checked

every 20 hours of use or weekly, whichever occurs more frequently.

• DO NOT disassemble the governor for any reason. Reorder correct speed – governor assembly (See Assembly Breakdown) and recheck free speed of tool

with a tachometer.

• Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters, ketones,

chlorinated hydrocarbons or nitro carbons.

• DO NOT clean or maintain tools with chemicals that have a low flash point (example: WD-40

• A Motor Tune-Up Kit (P/N 96532) is available which includes high wear and medium wear motor parts.

• Air tool labels must be kept legible at all times, if not, reorder label(s) and replace. User is responsible for maintaining specification information i.e.: Model #,

S/N, and RPM. (See Assembly Breakdown)

• DO NOT carry tool by air hose or near the throttle lever.

• Blow air supply hose out prior to initial use.

• Visually inspect air hoses and fittings for frays, visible damage and signs of deterioration. Replace damaged or worn components.

• Refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for safety information.

After maintenance is performed on tool, add a few drops of Dynabrade Air Lube (P/N 95842) to the air line and start the tool a few times to lubricate air motor. Check

for excessive tool vibration.

Handling and Storage:

• Use of tool rests, hangers and/or balancers is recommended.

• Protect tool inlet from debris (see Notice below).

• DO NOT carry tool by air hose or near the throttle lever.

• Protect abrasive accessories from exposure to water, solvents, high humidity, freezing temperature and extreme temperature changes.

• Store accessories in protective racks or compartments to prevent damage.

Model

Motor

Number

hp (W)

13511

1 (745)

13512

1 (745)

13515

1 (745)

13516

1 (745)

13517

1 (745)

13518

1 (745)

13519

1 (745)

13520

1 (745)

13531

1 (745)

Additional Specifications: Air Inlet Thread 3/8" NPT • Hose I.D. Size 3/8" or 10mm • Air Flow Rate Based At Max HP. • Air Pressure 90 PSIG Max

All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality pneumatic motors can most often

be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor bearings causing early failure.

It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is contingent upon proper use of our tools and

cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a lack of lubrication during the use of this tool.

5/8 - 11 Threaded Arbor

Index Key

No. Part # Description

1 95274

2 53626

3 95764

4 13066

5 13065

Maintenance Instructions

Machine Specifications

Sound

Air Flow Rate

RPM

Level

SCFM (LPM)

1,800

82 dB(A)

36 (1,019)

3,400

80 dB(A)

41 (1,161)

3,400

80 dB(A)

41 (1,161)

3,400

80 dB(A)

41 (1,161)

4,500

80 dB(A)

41 (1,161)

4,500

80 dB(A)

41 (1,161)

6,000

83 dB(A)

44 (1,256)

4,500

80 dB(A)

41 (1,161)

1,800

82 dB(A)

36 (1,019)

Extension Dynastraight

5/8" or 1" Combination Arbor

Hex Nut

6 13063

5/8" – 11 Threaded Arbor

7 13062

Screw

8 13067

Front Flange 5/8"

9 53628

Front Flange 1"

10 95138

Air Pressure

Wheel Arbor

PSIG (Bars)

Diameter Inch

90 (6.2)

5/8 or 1

90 (6.2)

1/2

90 (6.2)

5/8-11 Thread

90 (6.2)

5/8 or 1

90 (6.2)

1/2

90 (6.2)

5/8 or 1

90 (6.2)

5/8-11 Thread

90 (6.2)

5/8-11 Thread

90 (6.2)

5/8-11 Thread

Notice

Arbors

Spacer (2)

11 13018

Rear Flange

12 13021

Spacer

13 53627

Arbor 5/8" or 1" Diameter

Hex Nut

Weight

Length

Pound (kg)

Inch (mm)

4.6 (2.0)

17-5/16 (440)

4.4 (2.0)

18-5/8 (475)

4.2 (1.8)

18-5/8 (475)

4.7 (2.0)

18-5/8 (475)

4.4 (1.9)

18-5/8 (475)

4.7 (2.0)

18-5/8 (475)

4.4 (2.0)

18-5/8 (475)

4.4 (2.0)

18-5/8 (475)

4.2 (1.8)

17-5/16 (440)

1/2" Diameter Arbor

Spacer

Wheel Flange (2)

Arbor 1/2" Diameter

Height

Inch (mm)

1-7/8 (48)