HiB Beam 50 Istruzioni per l'uso
Sfoglia online o scarica il pdf Istruzioni per l'uso per Prodotti per la cura della persona HiB Beam 50. HiB Beam 50 2.
Anche per HiB Beam 50: Manuale di avvio rapido (2 pagine)
Stampa la pagina
This product is IP44 rated and suitable for installation in
&
zones:
2
Outside Zone
All installations must comply with guidelines which are based on a zonal
concept. The diagram above illustrates this concept and must be followed
to ensure the safe installation of electrical appliances in the bathroom.
These regulations apply to domestic installations only. Installations must be
made in accordance with the current IEE wiring regulations and relevant
building regulations. HiB recommends that all electrical bathroom
products should only be fitted by a suitably qualified, Part P registered
electrician.
Thank you for purchasing this HiB product.
Please read through these instructions carefully and refer back to them
during installation to ensure that your product is fitted safely and that it
retains its high quality finish.
Please retain this leaflet for future reference.
Before installation, ensure the domestic electrical mains supply to
which the mirror is to be connected is turned off. Before drilling,
ensure that there are no hidden cables or pipes in the wall.
Operation Instructions
To turn illumination on or off, wave hand under the sensor switch.
Heated Pad is only on when mirror is illuminated.
Care Instructions
Do not use abrasives or solvents when cleaning this product.
Wipe off all water spillages as soon as possible using a soft, damp cloth.
Aftercare Service
In the unlikely event that this product should fail please contact HiB
customer services, details shown below.
Charging Socket
The charging socket is suitable for charging and powering electric razors,
trimmers and electric toothbrushes. NB. On first use of the charger socket,
inserting the plug may prove to be stiff. Reasonable force may be required
to fully insert the plug. After a few uses, stiffness will ease and the socket will
function as normal.
T:
+44 (0)20 8441 0352
F:
+44 (0)20 8441 0219
Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN
©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try and make sure they are as accurate as possible. In the
interest of continuous product development, HiB reserves the right to alter specifications as necessary. E & OE.
Illuminated Mirrors
Beam 50
Beam 80
Boundary 60
Installation
1. Position the mirror in a suitable location (according to the zonal
diagram - Fig. 1), ensuring that the domestic electrical mains
supply is within reach of the cable connection point of the
product.
(Fig. 1)
2. Carefully mark the position of the mirror using a soft pencil
ensuring it is level. Remove the mirror and mark the mounting
points (see Fig. A) Please ensure that all marked mounting
points accurately match up with the fixing points on the
mirror.
3. Using a suitable drill bit, drill holes in the marked positions to a
suitable depth. If drilling through tile, use a ceramic drill bit.
4. Insert wall plugs level with the surface of the wall. If fitting to a
tiled surface, wall plugs should be inserted below the tile surface
to avoid cracking. NB. For plasterboard walls, specialist fixings
should be purchased, available from any DIY or hardware store.
5. Screw supplied fixings into wall plugs.
6. Ensure the domestic electrical mains supply to which the
mirror is being connected is turned off. Connect the domestic
mains supply to the terminal box according to the wiring diagram
opposite (Fig. B) overleaf.
7. Hang the mirror in position.
8. Switch the domestic electrical mains supply for the mirror back
on.
Mounting Points Diagram (Fig. A)
NB. These products must be installed with a minimum distance of 150mm
between the infra-red sensor switch and any adjacent wall or object to
ensure correct operation of the sensor.
E:
hib.co.uk
Art No. 79550500
/ Beam 60
Art No. 79550600
Art No. 79550700
/ Boundary 50
/ Boundary 80
Art No. 79540600
Hanging Landscape
REAR VIEW
mounting points
NB: Boundary can only be
hung portrait
FI#01 026 R181017
Art No. 79540500
Art No. 79540700
Ver No.
1.0 Jan 2019