Automatic Technology C03M V1 Istruzioni per l'installazione - Pagina 2
Sfoglia online o scarica il pdf Istruzioni per l'installazione per Mixer musicale Automatic Technology C03M V1. Automatic Technology C03M V1 2. Manural wall console
Anche per Automatic Technology C03M V1: Istruzioni per l'installazione (2 pagine)
Stampa la pagina
Clearing Travel Limits
with
the
Manual Console
a.
Ensure
the
key
is in
the
unlock
position.
b.
Press
and hold the
YELLOW
MODE button for
2 seconds
to
enter into setup
mode.
c.
The
word
"SETUP"
wiil iliuminate
nextto the
MODE button
and
the green,
red
and blue
LEDi willflash sequentiallyto
indicate the
console
is
in Setup mode.
d.
PressandholdtheBLUECLOSEbuttonfortwo(2)
seconds(thewordSETUPandBLUECLOSELEDwil
startflashing).
e.
Release
the
BLUE CLOSE
button. The limits
are now
cleared.
Ensure
you
set
the limits before proceeding.
Setting
the
Pedestrian Position.
a.
Ensure
the
key
is in
the
un
ock position
and
the travel limits
have been
set.
b.
Drive
the shutter
using
the
BLUE
0
CLOSE
button
or
the
GREEN
i
OPEN
button
to
the required pedestrian position.
c.
Press
and hold the
YELLOW
Mode button for
2 seconds
to
enter into setup
mode.
d.
The
word
"SETUP"
wil
illuminate
next
to the
MODE button
and
the green,
red
and blue
LEDi
will
flash sequentially
to
indicate the
console
is
in Setup mode.
e.
Press
and
ho
d the
GREEN
f
OPEN
button for
2 seconds
(GREEN
and
BLUE LED's
will
i
luminate
to
confirm the pedestrian
position).
Recalling
the
Factory
Default,
a.
Ensure
the
key
is in
the
un
ock position.
b.
Press
and hold the
YELLOW
MODE button for
2 seconds
to
enter into setup
mode.
c.
The
word
"SETUP" wi
I il
uminate
nextto the
MODE
button
and
the green,
red
and blue
LED's
willflash alternativelyto
indicate the
console
is
rn
Setup mode.
d. PressandhodtheREDSTOPbuttonfor'l
Oseconds(RUNandBLUELEDtwrll
flash).
Setting Adjustment.
a.
Ensure
the
key
is in
the
un
ock position.
b.
Press
and hold the
YELLOW
MODE button
for2
seconds
to
enter into setup
mode.
c.
The
word
"SETUP"
will illuminate
nextto the
MODE button
and
the green,
red
and
b ue
LED's
willflash alternativelyto
indicate the
console
is
in Setup mode.
d.
Press
and hold
the
RED STOP
button for
2 seconds (the
word
SETUP
will
be f
ashing).
SELECTION
PATTERN
and
SETTING
ouTl
@
ouT2
$
ourr
s:
!
euxhrut
,s
a
&
Mode
button
response
in
I
position
s
c
Lii\]I-GCK
Mode
z
ol
llJ
o-
UI
:)
CLOSED STATUS*1
CLOSE
IGNORED*
NOT AVAILABLE*
STOPPED
STATUS
&
sToP*
*
i-ji'j
+
;:i,ir
l-*Ci(
+
L0CK
I
*
CONSOLE
BUTTONS
only
*
oPEN
STATUS*2 !
OPEN ;
tt
@
CONTROL INPUTS
only
3
a
cLosrNG
STATUS
a
LIGHT
.s
G
@
s
I
LoeKe
LOCK
e
OPENING
STATUS
a
@
PEDESTRIAN
6
&
!-n
MOVING
STATUS*3
O
LIGHT
STATUS
*Default
Setti
Pressthe GREEN
f
OPEN
orthe
BLUE 0CLOSE
buttonsto
change
the
pattern.
Press
the
RED SET
button
to
enter
edit
mode (the
spanner
wili
start
i
ashing),
the
setting!
va
ue pattern
rs
now flashed,
refer
to
the table
above
to
obtain the corresponding
value.
g.
UsetheGREEN
f
OPENorthe
BLUE
!CLOSEbuttonstochangethevaluepatternofthatoftherequiredvalue.
h.
Press
the
RED SET
button
to
save
the
new value
or
press MODE
to
cance without
saving.
i.
Continue from step
e
to
edit another setting or
press MODE
to
exit
back
to
SETUP
N/lODE.
OUT1, OUT2
or
OUT3
VarioLrs
status signals
listed
in
the
table
above
can
be
used
from
OUTI
,
Olf
2
and OUT3
to contro
other
devices such
as
alarm,
dock
eve er
and
relays
etc.
A
transistor
controlled outputs
can
sink 100
\lA
MAX.
NOTE:
An Optional
Re
ay
Module
(RLM-O1)
with three
(3) relays
suitable
for
the
Manual Conso e
C03M
is
avai
ab
e
from
ATA.
AUX lnput
A normally open
push
button
can be
connected
across
0V and AUX
input.
By
default
it
will
act
as STOP
button. AUX input
can
be programmed
to
act
as
any of
the following:
close,
stop, open, light or pedestrian
push
button.
MODE
Button
reponse in
key
lock
position
The MODE switch can
be programmed
according
to the
requirements
to
act
differently
when
the
key
is in
the
lock
position. Referto the
column
"Mode
button
response in lock
position"
in
the table
above.
e
f.
aut9matic
TECHNOLOGY