ADEMCO 5816MN Istruzioni per l'installazione

Sfoglia online o scarica il pdf Istruzioni per l'installazione per Trasmettitore ADEMCO 5816MN. ADEMCO 5816MN 2. Door/window transmitter

Stampa la pagina

PLATE

MOUNTING

HOLES (2)

CASE

HOLDING

POSTS (2)

CASE

LOCKING

TAB

Figure 1. Mounting Plate

GENERAL INFORMATION

Each 5816MN Door/Window Transmitter has its own

unique serial number permanently assigned during

manufacture. The QED control unit is required to

"enroll" the transmitter ID at some point prior to its

usage in the alarm system. Refer to the QED control

unit's installation instruc tions for further details. Note:

During programming of the QED control unit, 5816MN

transmitters should be treated as "RF" (i.e. supervised

RF) Type ( mandatory for UL installations ).

The 5816MN can send two unique codes, the first for a

wired closed circuit contact loop and the second for its

built-in reed switch (used in conjunction with a magnet

as described below). A wired loop and/or reed switch

may be used. For UL installations, a contact may not

be more than 3 feet from the transmitter.

The 5816MN includes a built-in cover tamper which is

activated when the cover is removed.

MOUNTING

For proper orientation of the unit in relation to the

mounting plate, loop wiring, and/or magnet, read all of

this section before installing the unit.

The description that follows assumes that the unit will

be mounted as shown in the diagrams, with the magnet

(if used) located in one of the positions shown in Figure

2. The unit may, however, be installed in any direction,

as long as the relationship of the unit to its mounting

plate and (if used) magnet is maintained.

Although the unit can be mounted directly to a surface,

it is recommended that the mounting plate be used, for

ease in removing the unit for servicing should it

become necessary.

Before mounting the transmitter permanently, conduct

Go/No Go tests (see QED control's instructions) to

verify adequate signal strength and reorient or relocate

the transmitter if necessary.

Remove the transmitter's cover by inserting the

flat blade of a small screwdriver into the pry-off slot

at the end of the unit farthest from the cover's

decorative ribs (see Fig. 2 for location), and twist -

ing the blade.

Disengage the supplied mounting plate from

the unit by inserting the blade of a small screw -

www.PDF-Zoo.com

I NS TALLATI ON

I NS TRUCTI ONS

For use with QED control panels ONLY!

LOCATE

WIRE EXIT

HOLE IN

WALL HERE

(IF USING

CONCEALED

WIRING)

1/4" DIA. MAX.

DOOR/WINDOW TRANSMITTER

REED SWITCH (LOOP 2)

COVER

HOLDING

HOOKS

(2)

LOCKING TAB

RELEASE

WINDOW

(BENEATH

BATTERY)

ANTENNA

TAMPER

CONTACT

PINS

REED

SWITCH

COVER PRY-OFF

SLOT

ALTERNATE POSITION FOR

MAGNET

Figure 2. 5816MN (shown without cover)

driver into the locking tab release window (see Fig.

2) and pressing it against the locking tab (shown in

Fig. 1), while sliding the plate downward along the

case back.

Install the mounting plate, with its case holding

posts pointing up (in this example), in the location

selected as described in the QED control unit's

installation instruc tions. Use the flat head screws

supplied.

Note: If a wired contact loop is to be used, with

concealed wiring, the wire exit hole in the

wall should be in the location shown in

Figure 1, and no more than 1/4" in

diameter.

If a wired contact loop is to be used, feed

concealed wiring through the slot in the case back,

but do not connect to the ter minal block yet. For

surface wiring entry, a thin "breakout" area is

provided in the case wall (see Fig. 2 for location).

Attach the case back to the mounting plate by

sliding the key hole slots in the case back down

onto the mounting plate's case holding posts. The

locking tab will click as the case back locks in

place.

6. If one of the reed switches in the unit is to be

used, a No. 5899 Magnet (obtain separately)

should be mounted adjacent to the alignment

marks on the right side of the case, or adjacent to

the bottom of the case (see Fig. 2).

LOOP WIRING CONNECTIONS

With the battery still not inserted, connect the contact

loop wires to the unit's loop terminals (see Fig. 2).

Caution: Make sure that the bared sections of the

loop wires do not short to the reed switch.

The contact loop must use closed circuit devices. The

loop response time is a nominal 100mSec.

Note : If the contact loop is not to be used, no

connection is needed across the loop terminals.

N6747V1 4/98

5816MN

ALIGN MAGNET

BETWEEN MARKS

ON CASE

MAGNET

(OBTAIN

SEPARATELY)

1/2" MAX.

LOOP TERMINALS

(LOOP 1)

WIRE ENTRY HOLE

IN BACK OF CASE

BREAKOUT FOR

SURFACE WIRING

ACCESS

(If used)

(continued)