Gaither BEAD BAZOOKA BB6L2 Manuale - Pagina 9

Sfoglia online o scarica il pdf Manuale per Strumenti Gaither BEAD BAZOOKA BB6L2. Gaither BEAD BAZOOKA BB6L2 10.

Stampa la pagina

Set-up of your new Bead Bazooka® (Gaither's BB3L2 / BB6L2/ BB10L2 ) unit

Coupler Nipple (a)

( not included)

Before using the Bead Bazooka® you must install the following:

1) The air coupler nipple is not included. Install an air coupler nipple that fits your particular system into the

small intake valve (a) pictured above.

2)The slotted double barrel (b) must be installed into the large release opening shown in the above diagram.

Install and secure lock nut so that the slotted double barrel is securely tightened.

Using the Bead Bazooka® with the tire/wheel assembly in a horizontal position:

1.Adjust the slotted double barrel so that the barrel flange is on top (opposite side of the handle stock and trigger release) and paral-

lel to the ground.

2.Place the tire (any size up to medium commercial truck tire) so that the short side of the wheel is on the bottom and the long side

of the wheel is on the top. (see diagram #2 below) The valve stem should be pointed upward to the sky. At this point the Gaither

tire stand (GB-51) or block of wood should be holding the tire and wheel off the ground and the bottom bead should already be

seated properly. (Note: to ensure proper and perfect bead seat, tire and wheel should always be adequately lubricated)

3.Attach an airline to your air coupler nipple and open the intake valve to fill the air tank to the desired working pressure. (see proper

storage and unit charging recommendation –next page) Normal working pressure is from 20 to 150 psi / 1.5 to 10 Bar. The amount

of pressure that is needed in the tank depends on the tire size and condition of the tire. The Bead Bazooka® can help set the beads

to wheels on motorcycle, passenger, ATV, industrial, truck, and some small agricultural tires.

4.Using two hands; one on the handle stock with trigger protector and the other on the handle which is on top of the tank, direct the

slotted double barrel flange to the wheel exactly opposite the valve stem. (In most cases this is the best position but in some cases

with smaller tires it is better to position the barrel close to the valve stem) Once you are in position to fire the Bead Bazooka® you

may want to bring the barrel away from the wheel approximately 1" to 2" so that the barrel does not contact the bead as it quickly

rises from the force of air flow. Make sure there is no valve core in the valve stem and using an airline or the Gaither Whip Hose

(GB-52) apply a steady flow of air into the valve stem while simultaneously firing the Bead Bazooka®. For extreme cases: a

Gaither Tire Wedge (GB-53) or wedges may be used under the tire to help close extremely large gaps between tire and wheel. (See

Diagram #2)

5.Position the Bead Bazooka® so that the slotted

double barrel opening is pointing directly into

the largest gap between the tire and wheel.

Normally a 50-70 degree angle is the best.

6.Secure tightly the Bead Bazooka® with both

hands on both handles and place your index

finger onto the trigger. Pull gently to release

the air inside of the tank. Hold steady the unit

and always keep the air flow directed into the

gap between the tire and wheel. Note: If this

does not properly set the bead to the wheel,

repeat the procedure at a higher pressure. You

can also try to use the Bead Bazooka® in an

upright position (see next section)

Safety Release Valve

Pressure Gauge

Air Release Trigger

DO NOT PLACE THE BARREL FIRMLY

AGAINST THE RIM,

but instead it should be held 2-3" away from

the wheel flange when firing for better overall

lift and performance

Barrel (b)

Diagram #2