2GIS 2GIG-SDS1-345 Manuale d'uso

Sfoglia online o scarica il pdf Manuale d'uso per Accessories 2GIS 2GIG-SDS1-345. 2GIS 2GIG-SDS1-345 4. Smoke detector sensor

Stampa la pagina

INSTR,INSTL,2GIG-SDS1-345 - P/N: 10010592 X8- INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500" X 11.000" - TOL. +/- 0.020"- SCALE: 1-1 - PAGE 1 OF 2- FOLDING: FOLD 1X TO FINAL SIZE: 8.500" X 5.500"- FINISH WITH LOGO SHOWING

2GIG-SDS1-345

SMOKE DETECTOR SENSOR

GENERAL INFORMATION

The 2GIG Smoke Detector Sensor, part number 2GIG-SDS1-345, is a 110V AC

powered sensor. It monitors the interconnect line on interconnected hardwired

smoke detector systems and sends out a transmission when smoke is detected

at any of the smoke alarm units connected on the same circuit. The device has

LEDs to visually indicate the status of the sensor. A single CR2032 ba ery provides

backup power in the event that AC power is lost on the smoke detector system

circuit. The smoke detector sensor communicates with a compa ble 2GIG control

panel and can send alarm, low ba ery, AC power loss, and supervisory messages

to the system's receiver.

Contents of Carton:

• 1-Smoke Detector Sensor

• 2-2" long 10-32 Screws

• 1-CR 2032 3 Volt Coin Ba ery

CR2032

COIN BATTERY

CR2032

10-32 X 2"

SCREWS

Figure 1. 2GIG-SDS1 Kit

IMPORTANT: This device must be tested and maintained regularly. This device

is intended for use with compa ble smoke detectors, but will not detect the

presence of smoke, heat, or ﬁ re directly.

✓ Note: Each of the smoke alarms part of interconnected smoke alarms must be:

• Present in every required loca on per NFPA 72,11.5.1

• Conﬁ rmed as less than ten years from date of installa on (or manufacture).

Please check label on the device or original smoke detector device manual.

• Hardwired to a single, common 120V AC circuit designated for interconnected

smoke alarms.

• Pass the manufacturer's stated tes ng regimen to conﬁ rm proper interconnect

opera on.

• Have fresh back-up ba eries.

• On the list of compa ble models (any model not listed may work but has not

been compa bility tested.

• This device shall not be installed in loca ons where the normal ambient

temperature is below 40F(4.4C) or exceeds 100F (37.8C), unless the alarm has

been determined capable of being used at installa on points with higher or

lower ambient temperatures.

• Please see sec on at the end regarding informa on on the proper installa on

of smoke detectors that are intended to work with the Smoke Detector Sensor.

• This device is not intended to work with smoke alarms paired with smoke alarm

guards, unless the combina on has been evaluated and found suitable for this

purpose.

Compatible Smoke Alarm Models

• BRK Brands Model 7010B: AC Powered Photoelectric Smoke Alarm with Ba ery Backup

• Firex Kidde Model i4618: Hardwire Ioniza on Smoke Detector with Ba ery Backup

• First Alert BRK Model 9120B: Hardwired Smoke Alarm with Ba ery Backup

• Kidde Model i12040: 120V AC Wire-in Smoke Alarm with Ba ery Backup

• USI Electric Model 5304: Hardwired Ioniza on Smoke and Fire Alarm with

Ba ery Backup

PRINTER'S INSTRUCTIONS:

CAUTION: Before a emp ng installa on, locate the primary electrical circuit

that powers the interconnected hardwired smoke detector system and shut oﬀ

or disconnect power to this circuit. An electrical shock hazard is present if this

electrical circuit is not temporarily disabled during installa on.

WARNING: Remember to turn on or reconnect power to the primary electrical

circuit that powers the interconnected hardwired smoke detector system. The ﬁ re

warning system may be disabled if electrical power is not restored to the system

Install Sensor

Select a smoke detector that will be used to provide power and communicate to

the smoke detector sensor. Any smoke detector that is within range of a wireless

2GIG receiver can be selected if the smoke detector is part of an interconnected

hardwired system.

Remove the exis ng smoke detector from the exis ng moun ng bracket. This is

usually done by twis ng the detector counter clockwise or clockwise from where

it is mounted.

SMOKE DETECTOR

SENSOR

WIRETAPS

Figure 2. Remove Exis ng Smoke Detector from Smoke Detector Moun ng Bracket

Figure 3. Unplug Pigtail of Exis ng Smoke Detector

Unplug the exis ng smoke detector from the smoke detector pigtail. Loosen the

two screws used to hold the exis ng moun ng bracket and remove it from the

wall or ceiling.

Figure 4. Remove Exis ng Smoke Detector Moun ng Bracket from Wall or Ceiling

EXISTING

SMOKE

DETECTOR

MOUNTING

BASE

ROTATE

COUNTER

CLOCKWISE

TO REMOVE

SMOKE

EXISTING

SMOKE

DETECTOR

EXISTING SMOKE

DETECTOR

UNPLUG

SMOKE DETECTOR

FROM EXISTING

POWER PIGTAIL

EXISTING SMOKE DETECTOR

MOUNTING BRACKET

REMOVE EXISTING SMOKE

REMOVE

DETECTOR MOUNTING

EXISTING

BRACKET FROM WALL OR

SCREWS

CEILING

ACCESS HOLE

IN WALL OR

CEILING

EXISTING

SMOKE

DETECTOR

POWER

PIGTAIL