Hifonics Brutus BXi606 Manuale - Pagina 7
Sfoglia online o scarica il pdf Manuale per Amplificatore per auto Hifonics Brutus BXi606. Hifonics Brutus BXi606 12.
Stampa la pagina
BXi2607D MONO AMPLIFIER APPLICATIONS
Basic application
SINGLE AMP INSTALLATION PROCEDURE:
SINGLE AMP INSTALLATION PROCEDURE:
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out
puts with good quality RCA interconnect cables.
puts with good quality RCA interconnect cables.
2. Plug in the HFR-3 bass remote module into the amp REMOTE INPUT jack.
2. Plug in the HFR-3 bass remote module into the amp REMOTE INPUT jack.
3. Route a 0 gauge power cables directly to the vehicle battery with an in-line fuse.
3. Route a 0 gauge power cables directly to the vehicle battery with an in-line fuse.
4. Connect a 0 gauge ground cables directly to chassis ground with in 36" of the amp.
4. Connect a 0 gauge ground cables directly to chassis ground with in 36" of the amp.
- Be sure to remove any paint or primer from the ground point.
- Be sure to remove any paint or primer from the ground point.
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
5. Connect the subwoofer(s) in accordance to the diagrams below.
5. Connect the subwoofer(s) in accordance to the diagrams below.
6. Make sure the MASTER/SLAVE switch is in the MASTER position.
6. Make sure the MASTER/SLAVE switch is in the MASTER position.
Note: The amplifier will not work if the MASTER/SLAVE switch is in the Slave position
Note: The amplifier will not work if the MASTER/SLAVE switch is in the Slave position
DESIGNATED
*
MONO LINE INPUT
B OOS T
H FR - 3
M I N
M A X X
DUAL AMP INSTALLATION PROCEDURE:
DUAL AMP INSTALLATION PROCEDURE:
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out
puts with good quality RCA interconnect cables.
puts with good quality RCA interconnect cables.
2. Plug in the HFR-3 bass remote module into the amp REMOTE INPUT jack on the
2. Plug in the HFR-3 bass remote module into the amp REMOTE INPUT jack on the
Master amp. This will allow the Master amp to control both Master and Slave amps
Master amp. This will allow the Master amp to control both Master and Slave amps
with just one Bass Remote.
with just one Bass Remote.
3. Connect an RCA jumper cable from the Master amp MASTER OUTPUT to the
3. Connect an RCA jumper cable from the Master amp MASTER OUTPUT to the
Slave amp SLAVE INPUT.
Slave amp SLAVE INPUT. Note: This will "link" the amps so that the Master amp
Note: This will "link" the amps so that the Master amp
crossover switches will control both the Master and Slave amps. The Slave amp
crossover switches will control both the Master and Slave amps. The Slave amp
crossover switches will be bypassed.
crossover switches will be bypassed.
Amplifiers are stable to 2ohm linked
DESIGNATED
MONO OUTPUT
FROM HEAD UNIT
B OOS T
H FR - 3
M I N
M A X X
Master remote controls
both amplifiers when
LINKED
Linking two amps for single or dual subwoofer application
MASTER
SLAVE
FULL RANGE
STEREO LINE INPUT
NOT USED
Note: You can use the Radio/CD designated mono line output
or a full range stereo line output. For full range stereo line
output, you will need an optional "Y-Adaptor" as shown.
MONO
SUBWOOFER
REMOTE TURN-ON
CHASSIS GROUND
TO BATTERY + 12 Volts
VIA FUSE
4. Route two 0 gauge power cables directly to the vehicle battery with an in-line fuse.
4. Route two 0 gauge power cables directly to the vehicle battery with an in-line fuse.
5. Connect two 0 gauge ground cables directly to the chassis with in 36" of the amp.
5. Connect two 0 gauge ground cables directly to the chassis with in 36" of the amp.
- Be sure to remove any paint or primer from the ground point.
- Be sure to remove any paint or primer from the ground point.
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
6. Make sure the Master amp MASTER/SLAVE switch is in the MASTER position.
6. Make sure the Master amp MASTER/SLAVE switch is in the MASTER position.
Make sure the Slave amp MASTER/SLAVE switch is in the SLAVE position.
Make sure the Slave amp MASTER/SLAVE switch is in the SLAVE position.
7. Connect the subwoofer(s) in accordance to the diagrams below.
7. Connect the subwoofer(s) in accordance to the diagrams below.
8. Connect a 12 gauge jumper from Master amp speaker - to Slave amp speaker + as
8. Connect a 12 gauge jumper from Master amp speaker - to Slave amp speaker + as
shown below.
shown below.
POWER
+12V
GND
REM
SINGLE VOICE COIL
SUBWOOFER
POWER
+12V
GND
REM
-
Y-ADAPTOR
PARALLEL MONO
SUBWOOFERS
2 OHMS EACH MINIMUM
POWER
SPEAKER
-
-
+12V
GND
+
REM
SPEAKER
POWER
SPEAKER
-
-
+
+
-
-
+12V
GND
REM
DUAL VOICE COIL
SUBWOOFER
SPEAKER
POWER
SPEAKER
-
-
-
-
+
+
+12V
GND
REM
TWO SINGLE COIL
SUBWOOFERS
+
-
+
+
+
+
+
+
5