Autonics PSAN Series Manuale del prodotto - Pagina 3

Sfoglia online o scarica il pdf Manuale del prodotto per Strumenti di misura Autonics PSAN Series. Autonics PSAN Series 7. Display type pressure sensors
Anche per Autonics PSAN Series: Manuale (2 pagine), Manuale del prodotto (6 pagine), Manuale (13 pagine)

Stampa la pagina

Specifications

PSAN-

Model

□V01C□□-□

□01C□□-□

Pneumatic type model: Gauge pressure

Pressure Type

Fluid type model: Gauge pressure

Pressure

Negative

Static

Min display unit

0.1 kPa

Rated pressure

0.0 to -101.3

0.0 to 100.0

range

kPa

Display & setting

5.0 to -101.3

-5.0 to 110.0

pressure range

kPa

Display type

7 Segment LED, 4 ½ digit

Display accuracy

-10 to 0 ℃: ≤ ±1% F.S., 0 to 50 ℃: ≤ ±0.5% F.S.

Rated pressure

Rated

Max. pressure

×2

pressure ×2

01) Only for static pressure, rated pressure range 100.0 kPa model

02) The unit is sealed structure. It is based on atmospheric pressure 101.3 kPa.

Applicable

Pneumatic type

medium

(air, non-corrosive gas)

Connection type

Connector type

Cable

Ø 4 mm, 5-core, 2 m

Wire spec.

AWG24 (0.08 mm, 40-core), insulator diameter: Ø 1 mm

Front case: PC

Back case: (back port) PC /

Material

(bottom port) PBT+GF15%

Pressure port: Brass-nickel plated

Protection

Connector type: IP40 (IEC standard)

structure

Certification

ᜢ ᜹ ᜫ

Unit weight

Back port: ≈ 80 g (≈ 165 g)

(packaged)

Bottom port: ≈ 85 g (≈ 170 g)

12 - 24 VDCᜡ (ripple P-P: ≤ 10%)

Power supply

Allowable voltage

90 to 110% of rated voltage

range

Current consumption

≤ 50 mA

01)

Control output

NPN open collector output / PNP open collector output model

Load voltage

≤ 30 VDCᜡ

Load current

≤ 100 mA

Residual voltage

NPN: ≤ 1 VDCᜡ, PNP: ≤ 2 VDCᜡ

Hysteresis

According to output operation mode

Repeat error

±0.2% F.S. ±min display interval

Response time

2.5, 5, 100, 500, 1000 ms

Protection circuit

Output short over-current protection circuit

Insulation resistance

≥ 50 MΩ (500 VDCᜡ megger)

Dielectric strength

Between the charging part and the case: 1,000 VACᜠ 50 / 60 Hz for 1 min

1.5 mm amplitude at frequency of 10 to 55Hz in each X, Y, Z direction

Vibration

for 2 hours

Ambient temperature

-10 to 50 ℃, Storage: -20 to 60 ℃ (no freezing or condensation)

Ambient humidity

30 to 80%RH, Storage: 30 to 80%RH (no freezing or condensation)

01) Current output: ≤ 75 mA

02) Refer to 'Output operation mode'. ±1digit error may occur due to pressure unit operation.

Analog output

Voltage (1 - 5 VDCᜡ ±2% F.S)

Output impedance

1 kΩ

Linearity

≤ ±1% F.S

Zero-point

≤ 1 VDCᜡ ±2% F.S.

Span

≤ 4 VDCᜡ ±2% F.S.

Resolution

1/1000 or 1/2000 (different by pressure type and display unit)

Response time

50 ms

Minimum Display Interval

Pressure

Negative

Min display interval 0.1 kPa

Resolution

1/1000 1/2000 1/1000 1/2000 1/1000 1/2000 1/1000 1/2000

Display unit

MPa

kPa

0.1

kgf/cm

0.001

bar

0.001

psi

0.01

mmHg

0.4

inHg

0.02

mmH

0.1

01)

01) Multiply display value by 100.

PSAN-

PSAN-□1□□□-□

□C01□□□-□

or sealed gauge pressure

01)

Compound

1 kPa

0.1 kPa

-101.3 to 100.0

0 to 1,000 kPa

kPa

-101.3 to 110.0

-101.3 to 1,100 kPa

kPa

• Pneumatic type:

Rated pressure ×1.5

Rated pressure

• Fluid type: Rated

×2

pressure ×2

Fluid type (non-corrosive gas

and fluid that do not corrode

stainless steel 316L)

Cable type / connector type

Connector type: Ø 4 mm, 5-core, 2 m

Cable type: Ø 4 mm, 5-core, 3 m

Front case: PC

Back case: PA6

Pressure port: SUS304/SUS316L

Connector type: IP40 (IEC standard)

Cable type: IP65 (IEC standard)

Connector type: ≈ 88 g (≈ 173 g)

Cable type: ≈ 90 g (≈ 167 g)

02)

Current (DC 4 - 20mA ±2% F.S)

≤ ±1% F.S

≤ DC 4 mA ±2% F.S.

≤ DC 16 mA ±2% F.S.

70 ms

Static

Compound

0.1 kPa

1 kPa

0.1 kPa

0.001

0.1

0.001

0.01

0.001

0.01

0.1

Mode Setting

[M] for over 3 sec

[M]

02)

[▼]+[▲] for over 1

RUN

sec after remove the

external pressure

[▲] for over 3 sec

01) Max. / Min. pressure value is available to check by monitoring.

[Option external input model] Auto shift judgment level checking / setting is available when P-9 External input

terminal is set as SHFT. (no input displays 0)

Parameter Setting

• Some parameter are activated / deactivated depending on other parameters. Refer to

the description.

• The setting item name and setting value are cross-displayed on the display part.

• It returns to RUN mode when there is no additional key input for 60 sec in each

parameter group.

• Guaranteed write life: 100,000 times

• [M] key: Saves setting value and moves to next parameter

] key: Selects setting value

[▼], [▲

Parameter

P-1

Display unit

OUT

P-2

operation

mode

P-3

Output type

Response

P-4

time

Voltage low

P-5

limit scale

Voltage high

P-6

limit scale

Current low

P-7

limit scale

Current high

P-8

limit scale

External

P-9

input

terminal

Auto shift

P-10

output

01)

P-11 Lock

01) Condition: P-9. External input terminal SHFT setting

0.1

0.001

0.02

0.8

0.03

0.1

→

Parameter group

Preset setting

→

Zero-point

→

adjustment

Max / Min monitoring

→

/ Auto shift

01)

Display Default Setting range

[Negative / Compound pressure model]

kPa, KGC: kgf/cm

, bar, psi, mmHg, inHg, H2O: mmH

KPA

[Static pressure model]

UNIT

MPa, kPa, KGC: kgf/cm

MPA

HYS.M: Hysteresis

WIN: Window comparison output

HY-W: Hysteresis-Window comparison output

OUtM

OFF

AUTO: Auto sensitivity setting

F.OUT: Forced output control

OUT1

1O2O Normally open

1O2C Normally closed Normally open

NoNC

1O2O

1C2O Normally closed Normally open

1C2C Normally closed Normally closed

@5 2.5, 5.0, 100, 500, 1,000 ms

SPD

[Option voltage output model]

Min. rated pressure ≤ Low limit scale ≤ 90% of rated

A-1V

pressure

[Option voltage output model]

Low limit scale setting value + 10% of rated pressure

A-5V

10)0

≤ High limit scale ≤ Max. rated pressure

[Option current output model]

Min. rated pressure ≤ Low limit scale ≤ 90% of rated

A-04

pressure

[Option current output model]

Low limit scale setting value +10% of rated pressure ≤

A-20

10)0

High limit scale ≤ Max. rated pressure

[Option external input model]

HOLD: Hold

D-IN

HOLD

SHFT: Auto shift

[Option external input model]

OUT1, OUT2, ALL

ShOT

OUT1

LOC1: Parameter, preset, zero-point adjustment setting

lock / Monitoring value reset lock

LOC2: Parameter lock (available to check setting value)

LOCK

LOC1

OFF

→

[M] for over 3 sec

→

[M]

RUN

Displays 0.0 and

→

returns automatically

→

[M]

Reset or set: [▼]+[▲]

→

for over 1 sec

, bar, psi

OUT2

Normally open