DC SXD45A IS D Istruzioni per l'uso e la manutenzione
Sfoglia online o scarica il pdf Istruzioni per l'uso e la manutenzione per Lavastoviglie DC SXD45A IS D. DC SXD45A IS D 2.
Stampa la paginaOPERATING AND MAINTENANCE INSTRUCTIONS
POWER LAMP
(OPTIONAL)
DRAIN PUMP
REMOVE DRAIN
PLUG AND SWITCH
THE MACHINE OFF
TO START THE
AUTOMATIC DRAIN
PUMP CYCLE
POWER
SWITCH
PREPARATION
•
CHECK THE DRAIN PLUG IS PUSHED FIRMLY IN PLACE AND THE FILTER BOWL IS POSITIONED INTO THE OUTLET HOLE.
•
CHECK THE DETERGENT ( RED ) AND RINSE AID ( CLEAR ) SUPPLY TUBES, WITH FOOT VALVES - ARE SUBMERGED IN SUFFICIENT PRODUCT.
•
CHECK THE DOOR IS CLOSED AND PRESS THE POWER SWITCH - THE POWER GREEN LAMP WILL COME ON.
•
ALLOW 30 mins FOR THE MACHINE TO FILL WITH WATER AND REACH THE CORRECT WASHING TEMPERATURE. MACHINE READY LAMP WILL COME ON.
OPERATION
•
REMOVE ALL DEBRIS FROM THE ITEMS TO BE WASHED, BEFORE PLACING THEM INTO THE BASKET.
•
CLOSE THE DOOR, PRESS THE CYCLE START SWITCH - THE CYCLE LAMP WILL COME ON.
•
AT THE END OF THE CYCLE THE CYCLE LAMP WILL GO OUT - OPEN THE DOOR AND PULL OUT THE BASKET.
•
ALLOW EXCESS WATER TO RUN OFF BEFORE REMOVING.
ROUTINE MAINTENANCE
•
AT THE END OF A SESSION TURN OFF THE POWER SWITCH. DO NOT REMOVE THE FILTER BOWL AT THIS STAGE.
•
REMOVE THE DRAIN PLUG - THE WASH TANK WILL EMPTY. MACHINES FITTED WITH DRAIN PUMP WILL AUTOMATICALLY START TO PUMP THE WATER OUT.
•
COLLECT THE DEBRIS AND REMOVE FROM THE WASH TANK.
•
CLEAN AROUND THE WASH TANK, DOOR SURROUNDS AND HINGES WITH AN 'ADDIS'' TYPE WASHING UP BRUSH.
•
DO NOT USE CHLORIDE CONTAINING BASED CLEANING SOLUTIONS OR ABRASIVES WHEN CLEANING THE WASH TANK.
•
TAKE OUT THE FILTER BOWL - CLEAN THOROUGHLY AND REPLACE.
•
DO NOT ALLOW DEBRIS TO GO DOWN THE OUTLET HOLE AS THIS MAY DAMAGE YOUR MACHINE.
•
REGULARLY CHECK RINSE JETS AND WASH JETS ARE CLEAR OF DEBRIS OR LIME SCALE - REMOVE IF NECESSARY BY UNSCREWING THE RINSE ARM NUT
THAT HOLDS THE RINSE ARM IN PLACE - REMOVE THE RINSE PIN THAT HOLDS THE WASH ARM IN PLACE - CLEAN BOTH THOROUGHLY AND REASSEMBLE.
WATER SOFTENER REGENERATION
•
THE SALT LOW LAMP WHEN ON WARNS IF THE SALT CONTAINER IS EMPTY.
•
UNSCREW THE SALT CONTAINER LID LOCATED INSIDE THE WASH TANK AND FILL WITH GRANULAR CATERING SALT ( THE FULL CONTAINER WILL
APPROXIMATELY REGENERATE FOUR REGENERATION CYCLES & HOLDS 1 Kg OF SALT).ENSURE THE SALT CONTAINER LID IS SECURE AFTER FILLING.
•
REMOVE THE DRAIN PLUG FROM THE MACHINE DURING THE REGENERATION OF THE WATER SOFTENER.
•
THE MACHINE POWER SWITCH MUST BE OFF TO ENABLE THE REGENERATION CYCLE.
•
CLOSE THE DOOR AND PRESS THE REGENERATION SWITCH. THE WATER SOFTENER REGENERATION LAMP WILL COME ON.
•
THE REGENERATION OF THE WATER SOFTENER WILL TAKE AROUND 20 MINUETS AND WILL BE FULLY AUTOMATIC.
•
THE WATER SOFTENER REGENERATION LAMP WILL GO OUT AND THE MACHINE WILL SWITCH OFF AUTOMATICALLY AFTER THE REGENERATION
CYCLE IS COMPLETE. REMEMBER TO REPLACE THE DRAIN PLUG BEFORE RE-FILLING THE MACHINE.
•
MEDIUM-WATER HARDNESS MAY REQUIRE FOUR REGENERATIONS A WEEK. MEDIUM TO HARD-WATER HARDNESS MAY
REQUIRE DAILY REGENERATION.
RINSE ARM NUT
RINSE JETS
RINSE PIN
SERVICE CALLS TO RECTIFY FAULTS CAUSED BY `THE LACK OF ROUTINE MAINTENANCE` WILL BE CHARGED FOR AND YOUR WARRANTY MAY BE AFFECTED
SXD45A IS D / SXD50A IS D
CYCLE LAMP
CYCLE START
SWITCH
RINSE ARM
WASH
SALT CONTAINER
LID
WASH JETS
www.directcatering.co.uk
2 MINUTE ~ 3MINUTE
FOOT VALVES FOR
CHEMICAL
CONTAINER TUBES
FILTER
BOWL
OUTLET HOLE
CYCLE
WATER SOFTENER
SELECTION
REGENERATION
LAMP
LAMP
CYCLE TIME
WATER SOFTENER
SWITCH
START SWITCH
SALT LOW
MACHINE
LAMP
READY
LAMP
DRAIN PLUG