dynarex Bari+Max Manuale di avvio rapido - Pagina 2

Sfoglia online o scarica il pdf Manuale di avvio rapido per Sedia a rotelle dynarex Bari+Max. dynarex Bari+Max 2. Bariatric reclining wheelchair with elevating leg rest

Stampa la pagina

USE AND SAFETY

TO OPEN CHAIR

Open wheelchair by tilting to one side and

pushing down on seat rail until fully opened.

TO CLOSE CHAIR

First fold foot plates to vertical position.

Grab seat with both hands at front and back edge and lift.

Or, tilt chair to one side and lift up on seat rail.

BACK WHEELS

Large rear wheels should be inspected at

least once a month to ensure proper tightness. If wheel

wobbles or is loose, release lock nut and tighten axle bolt

slightly. Test for proper tightness by leaning chair to one

side and spinning adjusted wheel.

TIRES

Solid rubber tires need minimal maintenance, but

should be cleaned occasionally with a damp cloth. Replace if

tires become severely worn or cracking appears.

WHEEL LOCKS

Engage both wheel locks before getting in

or out of chair, leaning forward in chair, or while in an

elevator or wheelchair lift. Locks are engaged by pushing

handle completely forward. Pull

the handle back to release the

wheel locks. Adjustments to

locks are made by loosening or

Mounting

tightening nut on the carriage

Positions

bolt. Wheel lock shoe should be

embedded at least ⅛". Adjust

by sliding clamp toward rear

wheel while handle is engaged

in locked position. Tighten nut

and bolt to secure in position.

locking action

Test for correct

before actual use.

FRONT CASTERS

and lubricated occasionally. Lubricate by removing fork and

greasing caster stem bearings and wheel bearings.

Reassemble fork and wheel by tightening nuts until no play

remains, but wheels roll freely. If nut is too loose, caster will

shimmy, if too tight, chair will be hard to steer.

REMOVAL OF SWING-AWAY

FOOTRESTS/LEG RESTS

Release lock by pushing on the

front rigging lever. Swing foot

rest/leg rest out and sideways.

Lift to remove.

ADJUSTING LENGTH OF

FOOTREST/LEG REST

When adjusting length of

footrests or leg rests, user should

be sitting in wheelchair with feet

on the foot plates. Loosen cam

lock lever around support

assembly and push the release

button. Raise or lower foot plate

to desired position that will

provide maximum support of

thighs. Ensure release button is

fully engaged, tighten cam lock

lever. Front rigging should not be

so low that it causes

uncomfortable pressure to thighs

at front of seat upholstery.

ADJUSTING/ELEVATING LEG

REST

Lift foot plate on leg rest

assembly to desired position.

Carriage Bolt

Release leg rest assembly and it

Handle

and Nut

will automatically lock into place.

To lower, push the release lever

and lower foot plate to desired

position.

REMOVABLE ARMS

arms by depressing spring button

Wheel Lock

and lifting arms out of front and

Wheel Lock

rear sockets.

Shoe

Rear Wheel

USE AND SAFETY

(Continued)

Casters should be checked periodically

Hinge

Pins

Hinge

Plates

Adjustment

Holes

Cam Lock

Lever

Release Lever

Remove

GENERAL CARE

Wipe chrome parts with a clean, soft cloth at least once a

week. All metal parts can be cleaned with auto wax or similar

products. If exposed to moisture, dry immediately. Do not

use an abrasive cleanser that will scratch the ﬁnish.

Front Rigging

• DO NOT adjust or operate wheelchair without carefully

Release Lever

reading all instructions in this manual.

Front Rigging

Assembly

• DO NOT operate this wheelchair on roadways, streets or

any surfaces with vehicular trafﬁc.

Footplate

• DO NOT operate on inclines without proper assistance.

• When getting in and out of wheelchair or when in elevator

or wheelchair lift, wheel locks must be fully engaged.

• Wheelchair should be on a smooth, stable and level area

with wheel locks engaged before transferring user in or out

of wheelchair.

Front Rigging

Support

• Footrest should not be lower than 2½" from the ground to

ensure clearance.

Release

Button

• DO NOT stand on or apply weight to foot rests.

Footplate

• Before reaching or leaning forward, rotate casters to front of

Assembly

the wheelchair and engage wheel locks to help prevent

wheelchair from tipping over.

• When trying to extend arms over back, only reach as far as

your arm can extend without having to alter your seating

position. Do not lean over or apply weight to the top of

wheelchair back. This can cause wheelchair to tip over.

Hinge

Plate

• DO NOT stand on wheelchair.

WARNINGS