KitchenAid 2210725 Manuale di istruzioni per l'installazione - Pagina 6

Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Frigorifero KitchenAid 2210725. KitchenAid 2210725 17. 36" (91.4 cm) counter-depth refrigerator

Stampa la pagina

Style 2

Push the bulb end of the tubing into the

water valve as far as it will go. Slide the nut

forward and finger tighten. Tighten nut two

(2) more turns with wrench.

Plug in

refrigerator.

grounded

outlet

Plug power

supply cord into

grounded outlet.

power

supply

cord

Move refrigerator into final position.

Level refrigerator.

Remove base grille if it is installed.

• Open the refrigerator doors to 90°.

Style 1: Screw-on grille

• Find pockets located about 4 inches

(10 cm) in from each end of grille. Use

Phillips screwdriver to remove the screw

found in each pocket.

Do Not remove the Tech Sheets

fastened behind the grille.

Style 2: Snap-on grille

• Grasp the grille with both hands. Lift up

and tilt the top of the grill toward you.

Do Not remove the Tech Sheets

fastened behind the grille.

The roller adjusting bolts are located

behind the base grille.

Page 6

This refrigerator has 4 adjustable rollers (2

front and 2 rear). There are 2 sets of roller

adjusting bolts found at the base of the

refrigerator on each side. The yellow top

bolt will adjust the rear roller and the silver

bottom bolt will adjust the front roller.

bulb

nut

(provided)

10.

Use a 1/2" socket wrench to turn

the roller adjusting bolts. Turning the bolt

clockwise will raise the refrigerator and

counterclockwise will lower the

refrigerator. (NOTE: Be careful not to back

the roller bolts out of the roller brackets

when lowering the refrigerator. The bolt

head will start to back out toward you when

the roller is in its lowest position. If the

screw does come out of the rear roller

bracket, the compartment access cover on

the back of the refrigerator will have to be

removed to reinstall the bolt back into the

nut.)

1/8" (3 mm)

clearance for

leveling refrigerator

1/4" (6 mm)

clearance set for

full-overlay

cabinet doors

11.

Adjust the front rollers to bring the

refrigerator top parallel with the cabinet

above the refrigerator; leave about 1/8"

(3 mm) gap between the refrigerator top

hinge and the cabinet. (If you do not have a

cabinet above the refrigerator, adjust to

make the top level.)

12.

Adjust the rear bolts to bring the

refrigerator level with the side cabinets or

cabinet end panels.

13.

If desired, the 4 rollers may now

be raised to close the gap between the

refrigerator top hinge and the cabinet

opening. Check that all 4 rollers contact the

floor and the cabinet doors above the

refrigerator open fully.

3/4" (19 mm)

clearance set for

full-overlay cabinet

doors and

rear

refrigerator trim kit

adjusting

bolt

(yellow)

front

adjusting

bolt

(silver)

NOTE: Cabinets with full-overlay doors will

require 1/4" (6 mm) additional clearance

between the top hinge and cabinet to

prevent the doors from hitting the hinge

when opening. (If you have a trim/panel kit

on the refrigerator doors, 3/4" (19 mm)

additional clearance will be required to

prevent the cabinet doors from interfering

with the refrigerator door trims.)

14.

Replace the base grille.

• Open the refrigerator doors to 90°.

Style 1: Screw-on grille

• Place the grille in front of the base grille

area.

• Use a Phillips screwdriver and guide the

cabinet

screws through the grille holes and into

the screw clips located in the corner

plates on each side of the opening.

Tighten screws securely.

Style 2: Snap-on grille

• Place the grille lower clips into the holes

in the refrigerator panel. Roll the grille up

toward the refrigerator until it snaps into

place.

cabinet