Corby PLATINUM 7510 Istruzioni per l'installazione e la programmazione - Pagina 3

Sfoglia online o scarica il pdf Istruzioni per l'installazione e la programmazione per Tastiera Corby PLATINUM 7510. Corby PLATINUM 7510 4.

Stampa la pagina
LED will light for three seconds (to acknowledge the entry) and
then it will resume flashing fast. Re-enter your new master code
followed by the pound sign (#). The Red LED will light for three
seconds (to acknowledge the entry), and then it wi ll flash slow.
Your new Master Code is now valid. Be sure to make note of it
and keep it in a secure place. You are now back at the main
program menu.
Example:
To set Master Code to 382436, enter:
2 00 # 382436 # 382436 #
Add or Change a User Code
Enter 2 and th e Red LED wi ll li ght for three secon ds and then
flash fast. Enter the three-digit User Number (001 - 200) to be
added or changed followed by the pound sign (#). Preceding
zeros are optional and may be omitted here.
digit User Code followed by the pound sign (#). The Red LED will
ligh t for three sec onds ( to ack nowled ge the ent ry), then th e Red
LED will continue to flash fast. Re-enter the new User Code
foll owed by t he pound sign (#). The Red LED will light for three
seconds, and then it will flash slow. The new User Number and
User Code have been accepted. You are now back at the main
programming m enu. To add more users enter [2] and repeat the
above procedure for all desired User Codes.
Examples:
To add code 2468 i n User Sl o t 1, Enter:
2 001 # 2468 # 2468 #
To add code 55555555 in User Sl o t 55, Enter:
2 55 # 55555555 # 55555555 #
To change code for User 1 to 24680, Enter:
2 1 # 24680 # 24680 #
Erase an Individual User Code
Only the User Codes are erasable. The Master Code may be
changed but not erased. Enter 3 and the Red LED will light for
three sec onds and then it will begin to flash fast . Enter the User
Code you wish to erase, not the User slot number, followed by the
pound sign (#). The Red LED will light for three seconds (to
acknowledge the entry), then it will begin to flash slow. You are
now back at the main program menu.
Example:
To erase User 1 from previous example, enter:
3 24680 #
Erase all User Codes
Enter 4 and th e Red LED wi ll li ght for three secon ds and then
it will flash fast. Enter the Master Code, followed by the pound
sign (#). The Red LED will light for three seconds (to acknowledge
the entry), then it will flash very fast for 35 seconds while erasure
is taking place. When the Red LE D flas hes slo w agai n it i ndicates
that the erasure is completed. You are now back at the main
program menu.
Example:
To erase all users, enter: 4 382436 #
Note: Erasing all User Codes will not affect the Master Code.
which may be changed but not erased.)
Factor y Reset Function
Press t he RESET button on t he back of the k eypad. The Red
LED will light steady for 3 seconds and then continue to flash
Enter the 4 to 8
P
S
K
LATINUM
ERIES
EYPAD
slow. Enter 1234 #. The Red LED will light steady for 3 seconds
and then continue to flash slow while a continuous tone will be
heard. Press the RESET button on the back of the keypad once
again. The factory-set master is restored to 1234, the factory-set
user code is restored to 567890, and the door unlock time reverts
back to 5 seconds.
Troubleshooting
Here are some common problems you may find when using
the keypad, along with solutions to those problems.
1.
Symptom: The Red LED is no t displaying the prop er
sequence while programming.
Solution: Most likely, a step or key stroke was missed while
programming. There are two ways to recover if you end up in
this situation:
a.
Wait approximately 3 seconds until Red LED goes out,
then enter an asterisk (*) to remain in program m ode. The
Red LED will flash slow signifying that you are still in
program mode. Repeat desired programming.
b.
Wait approximat ely 21 s econds for the keypad to res et
itsel f. Dur ing this time t he keypad will beep fo r thr ee
seconds. The Red LED will go out for 15 seconds, and
the keypad will beep again. After the Red LED lights up
again for three seconds you will be out of the program
mode. Enter program mode by entering **, then your
Master Code, then ** a gain. Repeat des ired
programming.
2.
Symptom: The keypad does not respond when pressing the
keys.
Solution: Make sur e the keypad and all el ectronic dev ices
have been p roperly wired to t he power suppl y and t he power
has not been tu rned of f (See Installation and Wiring the
Keypad section).
3.
Symptom: The keypad responds but the door does not open.
Solution: There are two common causes for this type of
problem; one is related to programming and the other is
related to wiring. Here are two things to check to eliminate or
remedy these causes:
a.
Make sure the Green LED goes on and remains solid
when the code is entered. If not, the code that was
entered has not been programmed yet. Try programming
this code in to the keypad again (See Add or Change a
User Code in the Programming the Keypad section).
b.
Enter the Master Code and make sure the door opens
correctly. If not, re-check the keypad wiring and the
stri ke s integrit y (See Installation and Wiring the
Keypad section).
4.
Symptom: A User Code was deleted but it still works.
Solution: There was more than one user with the same code.
The keypad does not prevent someone from entering
duplicate codes, but it is a good idea to limit the use of
dupli cate co des. Fo r instance, let s say t hat Us er 2 and User
4 both had a User Code of 8888. When User 4 leaves the
company and his User Code is deleted using Function 3, it is
really the code for User 2 that is deleted (the first 8888 that
the program comes across) and the code for User 4 is still
there. All co des should be a ssigned. Otherwi se, if a user
select ed 5678 as a code, it may already be in use.
I
- P
3
NSTRUCTIONS
AGE