HIKOKI DV 13VSS Manuale di istruzioni per la movimentazione - Pagina 5
Sfoglia online o scarica il pdf Manuale di istruzioni per la movimentazione per Trapano HIKOKI DV 13VSS. HIKOKI DV 13VSS 8.
Stampa la paginaPRECAUTIONS ON USING IMPACT DRILL
1. Wear ear protectors with impact drills.
Exposure to noise can cause hearing loss.
2. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
SPECIFICATIONS
Voltage (by areas)*
Power input*
Reversible
No load speed
Drill chuck capacity
Steel
Capacity
Concrete
Wood
Full load impact rate
Weight (without cord)
* Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
Drill chuck spec.
Standard accessories
Keyed
Chuck wrench ............................... 1
Case .............................................. 1
Keyless
Depth gauge .................................. 1
Side handle ................................... 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
○ Impact Drill Bit (for concrete)
3.2 mm – 20 mm dia.
Optional accessories are subject to change without notice.
APPLICATIONS
○ By combined actions of ROTATION and IMPACT:
Boring holes in hard materials (concrete, marble,
granite, tiles, etc.)
○ By ROTATIONAL action:
Boring holes in metal, wood and plastic.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, inviting serious accident.
3. Before drilling into walls, ceilings or fl oors, ensure that
there are no concealed power cables inside.
4. When boring concrete or similar hard materials in
IMPACT mode, turn the rotational change lever to the
R-mark. (Fig. 9)
230 V
550 W
Yes
0 – 2900/min
13 mm
13 mm
13 mm
20 mm
29000/min
1.4 kg
3. Extension cord
When the work area is removed from the power source.
Use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Selecting the appropriate drill bit
○ When boring concrete or stone
Use the drill bits specifi ed in the Optional Accessories.
○ When boring metal or plastic
Use an ordinary metalworking drill bit.
○ When boring wood
Use an ordinary woodworking drill bit.
However, when drilling 6.5 mm or smaller holes, use a
metalworking drill bit.
5. Mounting and dismounting of the bit
For Drill chuck with chuck wrench (Fig. 1)
(1) Open the chuck jaws, and insert the bit into the chuck.
(2) Place the chuck wrench in each of the three holes in
the chuck, and turn it in the clockwise direction (viewed
from the front side). Tighten securely.
(3) To remove the bit, place the chuck wrench into one of
the holes in the chuck and turn it in the counterclockwise
direction.
For keyless chuck (Fig. 2)
(1) Open the chuck jaws, and insert the bit into the chuck.
To open the chuck jaws, hold the ring while turning the
sleeve in the counterclockwise direction (viewed from
the front side).
(2) Firmly grasp the ring and turn the sleeve in the clockwise
direction. Tighten securely.
(3) To remove the bit, fi rmly grasp the ring and turn the
sleeve in the counterclockwise direction.
(4) When the sleeve does not become loose any further, fi x
the side handle to retaining ring, hold side handle fi rmly,
then turn the sleeve to loosen by hand. (Fig. 3)
English
5