HIKOKI CV 18DBL Manuale di istruzioni per la movimentazione - Pagina 7
Sfoglia online o scarica il pdf Manuale di istruzioni per la movimentazione per Sega HIKOKI CV 18DBL. HIKOKI CV 18DBL 16. Cordless multi tool
Anche per HIKOKI CV 18DBL: Manuale di istruzioni per la movimentazione (16 pagine)
Stampa la pagina
MOUNTING AND OPERATION
Action
Removing and inserting the battery
Charging
Remaining battery indicator
How to use the LED light
Mounting the application tool
Switch Operation
Adjusting operating speed
Sawing
Sanding
Charging a USB device from an
electrical outlet
Charging a USB device and battery
from an electrical outlet
How to recharge USB device
When charging of USB device is
completed
Selecting accessories
*2
The tool is equipped with two modes: "Standard Mode" and
"AUTO Mode".
(1) Standard Mode
You can change the vibration frequency between 6000
to 20000 /min by adjusting the dial from "1" to "5".
(2) AUTO Mode
Depending on the workload, AUTO Mode "A" will
automatically change the vibration frequency to 15000
/min or 20000 /min. This has the eff ect of lowering
vibration and noise prior to and during operation.
Adjust the dial for the mode and speed that best suits your
task conditions and materials.
*1 Operating speed
Mode
Standard Mode
AUTO Mode
With AUTO Mode, the vibration frequency may not reach
20000 /min or return to 15000 /min depending on variables
such as the type of work or the attachment in use.
*2 Select accessories that are suited to a specifi c task.
For details contact HiKOKI Authorized Service Center.
MAINTENANCE AND INSPECTION
1. Inspecting the application tool
Continued use of a dull or damaged application tool
will result in reduced cutting effi ciency and may cause
overloading of the motor. Replace the application tool
with a new one as soon as excessive abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very "heart" of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
Figure
1
2
3
4
5
6
7
*1
8
9
11-a
11-b
12
13
―
Dial
Vibration Frequency
1 – 5
6000 – 20000 /min
No load: 15000 /min
A
With load: 20000 /min
4. Cleaning on the outside
When the power tool is stained, wipe with a soft dry cloth
or a cloth moistened with soapy water. Do not use chloric
Page
solvents, gasoline or paint thinner, for they melt plastics.
5. Storage
9
Store the power tool in a place in which the temperature
9
is less than 40°C and out of reach of children.
NOTE
9
Storing lithium-ion batteries.
9
Make sure the lithium-ion batteries have been fully
10
charged before storing them.
Prolonged storage (3 months or more) of batteries with
11
a low charge may result in performance deterioration,
11
signifi cantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
11
However, signifi cantly reduced battery usage time may
11
be recovered by repeatedly charging and using the
batteries two to fi ve times.
12
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
12
and purchase new batteries.
12
CAUTION
12
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
13
country must be observed.
Important notice on the batteries for the HiKOKI
cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when used with
batteries other than these designated by us, or when
the battery is disassembled and modifi ed (such as
disassembly and replacement of cells or other internal
parts).
NOTE
Due to HiKOKI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
7