Airfield 95A251 Manuale di montaggio - Pagina 5

Sfoglia online o scarica il pdf Manuale di montaggio per Giocattolo Airfield 95A251. Airfield 95A251 8.

Stampa la pagina

∨ ∨ ∨ ∨ ∨ ∨ ∨ ∨

∨ ∨ ∨ ∨

∨ ∨ ∨ ∨ ∨ ∨ ∨ ∨ ∨ ∨ ∨ ∨

Governor Mode

_*_ _*_ _*_ _*_

_**_ _**_ _**_ _**_

_***_ _***_ _***_ _***_

Motor Rotation

W W W W

Switching Frequency

// // // //

\\ \\ \\ \\

Low Voltage Cutoff Type

＿ˉ＿ˉ＿ˉ＿ˉ

ˉ＿ ˉ＿ ˉ＿ ˉ＿

Using Your New ESC

Improper polarity or short circuit will damage the ESC therefore it is your responsibility to double check

all plugs for proper polarity and first fit BEFORE connecting the battery pack.

Alert Tones

The ZTW ESC is equipped with audible alert tones to indicate abnormal conditions at power up.

1. Continuous beeping tone (****) – Indicates that throttle stick is not in the minimum position.

2. Single beeping tone followed by a one second pause (* * * *)– Indicates that the battery pack

voltage exceeds the acceptable range. (The ESC automatically checks and verifies the battery voltage

once the battery is connected).

Built-in Intelligent ESC Safety Functions

1. Over-heat protection: When the temperature of ESC exceeds 110 deg C, the ESC will reduce the

output power to allow it too cool.

2. Lost Throttle signal protection: The ESC will automatically cut power to the motor when it detects

a lost of throttle signal for 2 seconds, then the motor will emit continuous beeping tone.

POWERING UP THE ESC FOR THE FIRST TIME & SETTING THE AUTOMATIC THROTTLE

CALIBRATION

The ZTW ESC features Automatic Throttle Calibration to attain the smoothest throttle response and

resolution throughout the entire throttle range of your transmitter. This step is done once to allow the

ESC to "learn and memorize" your Transmitter's throttle output signals and only repeated if you change

your transmitter.

1.Switch your Transmitter ON and set the throttle stick to its maximum position.

2.Connect the battery pack to the ESC. Wait for about 2 seconds, the motor will beep for twice, then put

the throttle in the minimum position, the motor will also beep, which indicates that your ESC has got the

signal range of the throttle from your transmitter.

The throttle is now calibrated and your ESC is ready for operation.

ENTERING THE PROGRAMMING MODE

1. Switch your Transmitter ON and set the throttle to its maximum position.

2. Connect the battery pack to the ESC.

3. Wait until you hear two short beeps (

programming mode.

4. If the throttle stick is left in the maximum position beyond 5 seconds, the ESC will begin the

sequence from one function and its associated setting options to another. (Please refer to the table

below to cross reference the functions with the audible tones).

5. When the desired tone for the function and setting option is reached, move the throttle stick down

to its minimum position. ESC will emit two beeps (**) confirming the new setting has been stored.

6. The ESC only allows the setting of one function at a time.

Therefore should you require making changes to other function, disconnect the battery

Very Soft

Soft Acceleration

Start Acceleration

Rpm off

first range

Heli

second range

Heli

Reverse

Forward/

8kHz

16kHz

Reduce Power

Hard Cut Off

) confirming that the ESC has now entered the

●● ●● ●● ●●