KitchenAid Architect Series II KFGU766VSS Manuale di istruzioni per l'installazione - Pagina 3

Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Piano di cottura KitchenAid Architect Series II KFGU766VSS. KitchenAid Architect Series II KFGU766VSS 20. 30" (76.2 cm) and 36" (91.4 cm) gas built-in cooktop
Anche per KitchenAid Architect Series II KFGU766VSS: Dimensioni (1 pagine), Manuale delle dimensioni (1 pagine)

Stampa la pagina
IMPORTANT: Observe all governing codes and ordinances. Do
not obstruct flow of combustion and ventilation air.
It is the installer's responsibility to comply with installation
clearances specified on the model/serial rating plate. The
model/serial rating plate is located on the underside of the
cooktop base.
A. Model/serial rating plate
To eliminate the risk of burns or fire by reaching over heated
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
that projects horizontally a minimum of 5" (12.7 cm) beyond
the bottom of the cabinets.
The cooktop should be installed in a location away from
strong draft areas, such as windows, doors and strong
heating vents or fans.
All openings in the wall or floor where cooktop is to be
installed must be sealed.
Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
Grounded electrical supply is required. See "Electrical
Requirements" section. Proper gas supply connection must
be available. See "Gas Supply Requirements" section.
The cooktop is designed to hang from the countertop by its
side flanges.
The gas and electric supply should be located as shown in
"Installation Clearances" section so that they are accessible
without requiring removal of the cooktop.
Provide cutout in right rear corner of cutout enclosure as
shown to provide clearance for gas inlet, power supply cord,
and to allow the rating label to be visible.
IMPORTANT: To avoid damage, check with your builder or
cabinet supplier to make sure that the materials used will not
discolor, delaminate or sustain other damage.
Product Dimensions
A. 30
" (76.7 cm) on 30" (76.2 cm) models,
36 " (92.0 cm) on 36" (91.4 cm) models
B. 21" (53.3 cm)
C. 3" (7.6 cm)

Location Requirements

A
A
B
Installation Clearances
C
J
"
A. 30
(76.2 cm) on 30
"
36
(91.4 cm) models
B. Combustible area above countertop (shown by dashed box above)
"
C. 30
(76.2 cm) minimum clearance between top of cooktop platform
and bottom of uncovered wood or metal cabinet (24
minimum clearance if bottom of wood or metal cabinet is covered
by not less than
not less than No. 28 MSG sheet steel, 0.015
steel, or 0.024
installing a range hood see NOTES.*
"
D. 13
(33.0 cm) recommended upper cabinet depth
"
E. 1
(2.8 cm)
"
F. 20
(50.8 cm)
G. 18" (45.7 cm) minimum clearance from upper cabinet to countertop
within minimum horizontal clearances to cooktop
H. Grounded outlet - Locate within 24" (61.0 cm) of right rear corner of
cutout
I. 29" (73.7 cm) on 30" (76.2 cm) models; 35¼" (89.5 cm) on
36" (91.4 cm) models
J. 24" (61.0 cm) minimum countertop depth is required
K. 2 " (7.3 cm) minimum distance to rear combustible surface
L. Gas line opening - Wall: anywhere 5" (12.7 cm) below underside of
countertop. Cabinet floor: anywhere within 6" (15.2 cm) of rear wall
is recommended
M. 8" (20.3 cm) minimum distance to nearest left side combustible
surface.**
N. 8" (20.3 cm) minimum distance to nearest right side combustible
surface.**
30" (76.2 cm) Cooktop Overall: M + N must equal 48" (122.0 cm)
minimum + 29" (73.7 cm) cutout for cooktop or 77" (195.6 cm)
36" (91.4 cm) Cooktop Overall: M + N must equal 48" (122.0 cm)
minimum + 35¼" (89.5 cm) cutout for cooktop or 83¼" (211.5 cm)
**M + N combined must be at least 48" (122.0 cm) minimum overall
Example 1: M = 8" (20.3 cm) left side + N = 40" (101.6 cm) right side
= 48" (122.0 cm)
Example 2: M = 24" (61.0 cm) left side + N = 24" (61.0 cm) right side
= 48" (122.0 cm)
NOTES:
C
After making the countertop cutout, some installations may
require notching down the base cabinet side walls to clear the
cooktop base. To avoid this modification, use a base cabinet with
sidewalls wider than the cutout.
If cabinet has a drawer, a 4" (10.2 cm) depth clearance from the
countertop to the top of the drawer (or other obstruction) in base
cabinet is required. The drawer depth may need to be shortened
to avoid interfering with the regulator.
*If installing a hood above the range, follow the hood instructions
for dimensional clearances above the cooktop surface.
A
B
F
K
E
H
L
I
M
"
"
(76.2 cm) models; 36
(91.4 cm) on
"
[0.6 cm] flame retardant millboard covered with
"
"
"
[0.06 cm] aluminum or 0.020
D
G
N
"
[61.0 cm]
[0.04 cm] stainless
[0.05 cm] copper). If
3