Green Brook PSPT1G Istruzioni per l'installazione

Sfoglia online o scarica il pdf Istruzioni per l'installazione per Interruttore Green Brook PSPT1G. Green Brook PSPT1G 2. Ip66 rated weatherproof 7 day fused timer spur switch

Stampa la pagina

Enclosure Installation Instructions

Ensure that mounting surface is flat and free from loose particles and dirt.

Remove the fitted product by lifting the lid and unscrewing the two screws. Then

remove the upper portion from the back box by removing the 4 screws on

installation. Please note that it is important to use a screwdriver of a size that allows

you to properly tighten these screws on installation.

Take the back box and when necessary drill a small hole through the drainage

point that will be at the lowest point when mounted. This is necessary to ensure that

any residual

moisture or condensation has an escape route at the back of the box.

Use a suitable drill/wall plug for the surface on which you are mounting your

weatherproof enclosure and use No.8 countersunk screws (not supplied) to secure

the back box through the 4 corner holes.

Remove a suitable cable entry cover by pushing through from the inside of the

back box.

If circumstances permit the best entry point for the supply cable is the bottom one.

If cable entry is via 20mm conduit use the conduit gland to secure the conduit to

the back box. If entry of cable is to be direct use a suitable IP rated cable gland.

Use only 3 core mains cable of sufficient rating for your application.

Screw down the upper portion to the back box ensuring the collar seal is in position

between the mating surface.

See the instructions below on how to connect individual product.

Mount the accessory onto the box using the screws as removed in step 2. Ensure

the screws are securely tightened.

Your weatherproof accessory is designed so that IP66 rating can be maintained when an

appliance is plugged into the socket. This is only achieved when the cover is pressed

down firmly so that the cable runs through the centre, and is fully enclosed by the

special seal. Always ensure that the cover is located correctly in place. If in doubt,

consult a qualified electrician.

Cleaning

If the unit needs cleaning it should be disconnected from the mains supply. Wipe

the surface with a dry cloth. Do not use a damp or wet cloth or a solvent based

cleaning agent, as this may damage or impair the safety of the product.

Disclaimer

This equipment is intended for domestic & light commercial use only. It must be

installed in accordance with these fitting instructions. It should be fixed in the

approved & conventional way to a solid or suitably safe surface.

The equipment should be connected to a mains supply of the appropriate voltage

(indicated on the product). If you are unsure, consult a qualified electrician before

fitting. No liability can be accepted if this product is installed or used in any other

way.

PLEASE NOTE: Electricity is dangerous and can kill. If you are in any doubt of how to

fit your product or there appears to be damage to the wiring, please consult a

qualified electri

cian.

TECHNICAL INFORMATION

Display:

Working Voltage:

Rated Impulse Voltage:

Operating Temp:

Operation:

Max Load:

Resistive -

Inductive -

Isolation:

Dimensions:

Conforms to:

IP Box Conforms To:

Your PowerBreaker Protekt IP66 Fused Timer Spur

Switch is guaranteed for 5 years from

the date of purchase.

This is in addition to your statutory rights.

Please keep these instructions for future reference.

INSTALLER - Please pass instruction manual onto the owner of the unit.

WEST ROAD . HARLOW

ESSEX . CM20 2BG . UK

[email protected]

www.greenbrook.co.uk

LCD

230V-50Hz

2,500V

-5°C to +40°C

Integrated Control

13A

Double Pole Isolation Switch

W137 x H132 x D80mm

BS 1363-4:1995+A4:2012,

BS EN 60730-1:2011,

BS EN 60730-2-7:2010.

IEC 60670-1 & IEC60670-22

GUARANTEE

IP66 Rated Weatherproof

7 Day Fused Timer Spur Switch

PowerBreaker Protekt products are suitable for use outdoors in severe conditions of rain

and water spray as well as dust contamination to IP66 as defined by BS EN 60529.

All products are for use with a 230V 50Hz supply.

INSTALLATION GUIDE - IMPORTANT

This product should be installed by a competent person and in accordance with the

current IET Wiring Regulations. If in doubt, consult a qualified electrician

Important -

•

Always disconnect the mains supply via the switch in the main fuse board or

consumer unit before commencing any electrical work.

•

Ensure that all terminal screws are fully tightened and that earth wires are sleeved

and that no bare wires are showing.

•

Cable glands must be used which maintain the IP rating. The warranty is invalid if IP

rating is not maintained.

Opening the Lid

To open the lid use your thumbs to un-clip the end

snap-shut clips. The lid should then pop open.

NOTE: For full Installation instructions for the

enclosure please see back page.

Operating Instructions

'ON' Indicator

Fuse

Holder

Dia.1

RESET THE DEVICE

1. To fully reset this unit press the recessed 'Reset'

button with a insulated blunt probe.

2. A full display will show when the battery is charged,

then revert to the default screen (

display indicates that the battery requires charging

for a minimum 3 hour period. (Dia.2 - Full display)

SETTING THE DAY OF WEEK

AND TIME

Note: Time setting is 24 hour mode.

1. Press the 'TIME' button for 2 seconds. Day of

week will start flashing (example shows 7 Day

setting Dia.3)

2. Use the '+' or '-' button to change the dis

play to the correct day of the week.

3. Press the 'TIME' button and the hour digits will

flash.

(Dia.4)

4. Use the '+' or '

' button to set the hours.

5. Press the 'TIME' button and the minute digits will

flash. (Dia.5)

6. Use the '+' or '-' button to set the minutes.

7. Press the 'TIME' button to save the setting

and return to operating mode.

Note: If '+' or '

' button is held for more than 2

seconds, the selected time digit will add or decrease

quickly (about 5 steps per second), if no key is

pressed within 60 seconds the display will return to

operating mode.

rote

- PSPT1G

Snap-Shut Clips

(Lift to open)

Programme

Reset

Button

Time

Button

'+' and '-'

Button

Front Cable

Entry

Double Pole

Isolation Switch

Dia.2

). No

Dia.3

Dia.4