KitchenAid KEC Manuale di istruzioni per l'installazione - Pagina 4
Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Piano di cottura KitchenAid KEC. KitchenAid KEC 16. Electric cooktop
Anche per KitchenAid KEC: Manuale di istruzioni per l'installazione (16 pagine), Manuale di istruzioni per l'installazione (10 pagine)
Stampa la pagina
- 1. Table of Contents
- 2. Installation Requirements
- 2. Electrical Requirements
- 3. Installation Instructions
- 3. Install Cooktop
- 3. Attach Cooktop to Countertop
- 4. Si_Curiti_ de la Table de Cuisson
- 5. Exlgences D'INSTALLATION
- 6. Instructions D'installation
- 7. Fixation de la Table de Cuisson Au Plan de Travail
• The cooktop s hould beconnected directly t othe junction b ox
•
through f lexible, armored ornonmetallic
sheathed, copper
•
cable. The flexible, armored cable extending from thefuse
boxorcircuit breaker boxshould b econnected directly t othe
junction b ox.
• Locate t hejunction b oxtoallow asmuch slack aspossible
•
between thejunction b oxandthecooktop s othatthe
cooktop c anbemoved i fservicing becomes necessary inthe
future.
Donotcuttheconduit. Use thelength o fconduit provided.
AULlisted orCSA approved conduit connector must b e
provided ateach endofthepower supply cable (atthe
cooktop a nd atthejunction b ox). Alisted conduit connector
isalready provided atthecooktop.
Ifthehouse h as aluminum w iring follow theprocedure below:
1. Connect asection o fsolid copper wire tothepigtail
leads.
2. Connect thealuminum w iring totheadded section o f
copper wire using special connectors and/or tools
designed andULlisted forjoining c opper toaluminum.
Follow theelectrical connector manufacturer's
recommended
procedure. Aluminum/copper
connection must c onform with
local c odes a ndindustry a ccepted wiring practices.
INSTALLATION
INSTRUCTIONS
Excessive Weight Hazard
Use two or more people to move and install cooktop.
Failure to do so can result in back or other injury.
Decide on the final location for the cooktop. Avoid drilling into or
severing existing wiring during installation.
1. Using 2 or more people, place the cooktop upside down on a
covered surface using the foam end posts from the
packaging. Make sure that the knobs are not resting on the
foam.
2. Remove foam strip roll from the package containing literature.
The roll contains four 1¼,, ( 0.64 cm) strips of foam. Remove
one strip at a time and apply foam strip adhesive-side
down
around bottom of the cooktop glass.
NOTE: The foam strip helps avoid damage to the underside
of the cooktop glass from debris and helps the cooktop sit
flat on uneven counters.
ii
..... ,,,ty
,,,_S
......_,f,,'J_
A. Cooktop base
B. ¼" (0.64 cm) Foam strip
C. Cooktop
_:_a_
_ __._i_4_ ¸¸_ _
Style 1: Cooktop
over undercounter
built-in oven
IMPORTANT: Clamping brackets should not be used.
1. Using 2 or more people, place cooktop right side up into the
cutout.
NOTE: Make sure that the front edge of the cooktop is
parallel to the front edge of the countertop.
If repositioning
is
needed, lift entire cooktop up from cutout to avoid scratching
the countertop.
Style 2: Cooktop
over cabinets
1. Determine whether your cabinet construction
provides
clearance for installing clamping brackets at cooktop base
ends.
30" (76.2 cm) and 36" (91.4 cm) traditional models
2.
......................
A
c
A. Cooktop base bottom
B. Attachment
screw
C. Clamping bracket
The clamping brackets can be installed before or after the
cooktop is placed into the cutout. Complete the following
steps for the option you choose.