Century Helicopter Products Hummingbird Elite 3D Pro Manuale di montaggio e istruzioni - Pagina 10
Sfoglia online o scarica il pdf Manuale di montaggio e istruzioni per Giocattolo Century Helicopter Products Hummingbird Elite 3D Pro. Century Helicopter Products Hummingbird Elite 3D Pro 12.
Anche per Century Helicopter Products Hummingbird Elite 3D Pro: Manuale di istruzioni (10 pagine)
Stampa la pagina
Section 13: Tail Rotor Assembly
Bags Used:
CNE321, CNE317, CNE324, CNE322
Tail gearbox assembly (13-1, 13-2)
52) Attach CNE317
Vertical Fin
included
M2x7.5 Self Tapping
by installing the
Gearbox
CNE321 to the back end of the
53) Attach the long arm of the
using the
M2x4 Machine
Pitch Slider Pin
on the
Tail Pitch
Tail Pitch Lever Mount
on the
54) Assemble CNE324
Tail Blade Grips
locktite on the included
M2x6 Machine Screws
into place. Attach the
Blade Grips
Pitch Slider Arms
using the provided
55) Install CNE322
Tail Rotor Blades
the provided
M2x7 Machine
portion of the
Tail Rotor Blades
the helicopter from the right side.
After completing step 55 check over each
step for completeness and continue to the
3D Pro 95% ARF Instruction manual to set
up and install electronics.
WARRANTY INFORMATION
Your new equipment is warranted to the original purchaser against manufacturer defects in material and workmanship for 30 days from
the date of purchase. During this period, Century Helicopter Products will repair or replace, at our discretion, any component that is
found to be factory defective at no cost to the purchaser. This warranty is limited to the original purchaser and is not transferable.
This warranty does not apply to any unit which has been improperly installed, mishandled, abused, or damaged in a crash, or to any unit
which has been repaired or altered by any unauthorized agencies. Under no circumstances will the buyer be entitled to consequential or
incidental damages. This limited warranty gives you specific legal rights. You also have other rights which may vary from state to state.
10
to the
Tail Gearbox
left side using the
Screws. Finish assembling the
found in parts bag
M2x7 Machine Screw
Tail
Gearbox.
Tail Pitch Lever
to
The Rudder Pushrod
Screw. Attach the short arm to the
Slider. Attach the center to the
Tail
Gearbox.
to the
Tail Rotor
Hub. Use
to attach the
Tail Blade Grip Arms
M2x6 Machine
Screws.
to the
Tail Blade Grips
Screws. The curved (leading edge)
must turn clockwise when viewing
Note) CNE209 is not used
until the 3D Pro 95% ARF
instruction manual.
13-1
M2x4 Machine
Tail
Screw
#CNE321
M2x8 Machine
Screw #CNE321
Tail Rotor
Tail
Hub
#CNE318
Tail Blade
Grip
#CNE324
Tail
M2x6 Machine
Screws
to the
Tail
#CNE324
using
13-2
M2x7 Machine
Screws
#CNE317
M2x4
Machine
Screw
#CNE317
Tail Pitch
Lever
#CNE321
Tail Pitch Slider
Pin Mount
Tail Pitch
Slider Pin
M2x6 Machine
Screws
#CNE324
Tail Rotor
Blade
#CNE322
Vertical Fin
#CNE317
Tail Pitch
Slider Arms
Tail Blade
Grip
#CNE324
M2x7 Machine
Screws
#CNE317
Rudder Pushrod
#CNE316