Century Helicopter Products Hummingbird Elite Series CP Manuale di istruzioni - Pagina 4

Sfoglia online o scarica il pdf Manuale di istruzioni per Giocattolo Century Helicopter Products Hummingbird Elite Series CP. Century Helicopter Products Hummingbird Elite Series CP 12. Elite series helicopter

Stampa la pagina

Century Helicopter Products Hummingbird Elite Series CP Manuale di istruzioni

Section 2

TESTING AND PREPARATION OF RADIO EQUIPMENT

PLEASE DON'T SKIP THIS SECTION

Before modifying or installing any radio gear,

please take a few minutes to test everything

as shown. Time spent becoming familiar with

the equipment and testing all the components

can prevent difficulty.

1. Install the crystals into the transmitter and

receiver. Be certain that the channel

frequency matches.

2. Note that all electronics plug into the receiver with the wires as pictured (orange wire faces

receiver label). Follow the diagram for each electronic connection. Once the electronics

system is connected and the transmitter is turned on, follow this step-by-step process to

check your equipment.

STEP-BY-STEP COMPONENT TEST

IMPORTANT:

1. Turn on the transmitter - Does

All connections shown in

the green LED turn on?

this manual work for

Futaba, Hitec & Century

2. Plug the "Bird Seed" battery

radio systems. If you

have any other radio

into your mixer board and wait for

system please consult

the flashing LEDs on the mixer

your radio instructions

board and the gyro to stop

for channel numbering.

flashing.

(some equipment may

differ in appearance.)

ELECTRONIC CONNECTION OVERVIEW

This diagram represents the

overall connections for wiring

the Hummingbird Elite

correctly. This diagram

includes the separate

connections pictured above.

IMPORTANT:

If you have the FP and

Century Lightning 4

channel radio please

refer to the wiring

diagram provided with

the radio system.

MODIFYING THE SERVOS FOR INSTALLATION

1. A long half arm may have to be created by

cutting a full or cross arm.

2. After testing the radio equipment the servos

will be in their center position. Remove the servo

retaining screw and servo wheel. Replace the

wheel with one of the long half arms. See section

3 for the final positions for your version.

3. Some servo arms require widening the hole in the arm in order for them to accept the

Hummingbird's pushrods using a #55 drill bit [1.34mm or 0.052"].

Connection And Diagnostics F

Connection And Diagnostics For The

Connection And Diagnostics F

Electronic Components

3. Move the right hand stick on

the transmitter left to right -

does the aileron servo move?

4. Move the right hand stick

forward and back - does the

elevator servo move?

Century Micro

Receiver

CN2032

1 2 3 4 5 6

Channels

Note:

Aileron Servo (ch.1)

Signal (s)

Positive (+)

CN2023

Negative (-)

(move left & right)

Elevator Servo (ch.2)

CN2023

Tail Motor

(move front & back)

(ch.4) CNE019

(turn left & right)

Throttle Connection

Back of Hummingboard

Servo Connections

6 5 4 3 2 1

Channels

Rudder & Gyro Connections

1 2 3 4 5 6

Channels

Motor Connections

The mixer speed controller controls the amount of power

transfered to the main and tail motors in proportion.

Collective

Pitch Servo

(ch.6 CP only)

CN2023

(blade pitch)

Micro Gyro

CN2022E

There are 2 wires coming from the upper

left corner of the board. The top wire is

marked rudder on the front of the board.

This wire goes into the gyro. Bottom wire

Gyro: signal faces

goes to the receiver for the throttle.

signal connection

Main Motor

(ch.3) CNE056

(go up & down)

or The

Ch#1

Ch#6

Ch#2

Aileron

Pitch (CP)

Elevator

The gyro helps

the helicopter

maintain rudder

heading. Without

the gyro the

helicopter might

spin out of

control.

Front of

Hummingboard

Bird Seed Battery

7 Cell 8.4V

CNE050

Bird Seed Battery

8 Cell 9.6V

CNE050A (optional)

Mixer and speed control Board

CNE052

Connect the tail motor and main motor

connectors to the board, note that the

two red wires are beside each other when

connected to the board as marked by

positive and negative indicators.