IKEA IH3402YS0 Istruzioni per l'installazione e manuale d'uso e manutenzione - Pagina 5

Sfoglia online o scarica il pdf Istruzioni per l'installazione e manuale d'uso e manutenzione per Cappa di ventilazione IKEA IH3402YS0. IKEA IH3402YS0 40. 30" (76.2 cm) range hood

Stampa la pagina
Parts Needed
•
7" (17.8 cm) round metal vent system
•
Wall or roof cap with damper to match vent system
•
1 - 75W max, 120V incandescent
light bulb
•
3 - UL listed wire connectors
•
Vent clamps/duct
tape as required
For cabinets
with recessed
bottoms:
•
Two 2" (5.1 cm) wide filler strips. Length and thickness
determined
by recess dimensions.
•
Four flat head wood screws or machine screws with washers
and nuts (to attach filler strips).
IMPORTANT:
Observe all governing codes and ordinances.
•
It is the installer's responsibility
to comply with installation
clearances specified on the model/serial rating plate. The
model/serial
rating plate is located inside the range hood on
the left wall.
Range hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used.
Given dimensions
provide minimum clearance. Consult the
cooktop/range
manufacturer
installation instructions
before
making any cutouts.
Grounded electrical outlet is required. See "Electrical
Requirements"
section.
All openings in ceiling and wall where range hood will be
installed must be sealed.
These range hoods are factory set for vented installations.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured
Home Construction
Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction
and Safety, title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured
Home
Installation 1982 (Manufactured
Home Sites, Communities
and
Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local
codes.
Product Dimensions
J
4 _5/ld '
(12.5 crn)
7/8"
.2 cm)
1 "
(2.5crn)
B
A
E
A. 18" (45. 7 cm) min. clearance - upper cabinet to countertop
B. 18" (45. 7 cm) to 24" (61.0 cm) suggested max. - bottom of range
hood to cooking surface
C. 30" (76.2 cm) min. cabinet opening width
D. 13" (33.0 cm) cabinet depth
E. 36" (91.4 cm) base cabinet height
•
Vent system must terminate to the outdoors.
•
Do not terminate the vent system in an attic or other enclosed
area.
•
Do not use a 4" (10.2 cm) laundry-type
wall cap.
•
Use a 7" (17.8 cm) round metal vent. Rigid metal vent is
recommended.
Plastic or metal foil vent is not recommended.
•
The length of vent system and number of elbows should be
kept to a minimum to provide efficient performance.
For the most efficient
and quiet operation:
•
Use no more than three 90 ° elbows.
•
Make sure there is a minimum of 24" (61 cm) of straight vent
between the elbows if more than 1 elbow is used.
•
Do not install 2 elbows together.
•
Use clamps or duct tape to seal all joints in the vent system.
•
The vent system must have a damper.
•
Use caulking to seal exterior wall or roof opening around the
cap.