KitchenAid Briva KIDS42EP Dimensioni del prodotto
Sfoglia online o scarica il pdf Dimensioni del prodotto per Lavastoviglie KitchenAid Briva KIDS42EP. KitchenAid Briva KIDS42EP 1. Kitchenaid dishwasher user manual
Stampa la pagina
PRODUCT MODEL NUMBERS
KIDS36EP
KIDS42EP
Electrical: 120-volt, 60-Hz, AC-only, 15- or
20-amp. electrical supply. Use copper wire only.
A time-delay fuse or circuit breaker and separate
circuit is recommended.
If using a Hot Water Accessory Tank and/or a
garbage disposer, a separate 120-volt, 60 Hz,
AC-only, 15- or 20-amp fused electrical supply
is required for each devise.
Water: For dishwasher, a hot water line with
20-120 psi (138-827kPa) water pressure. Water
temperature must be minimum 120°F (48.9°C)
at dishwasher. Use 3/8" O.D. copper tubing with
compression fitting is recommended. Use a 90°
elbow with 3/8" N.P.T. external pipe threads on
one end to connect to water inlet valve. Do not
solder within 6" (15.2 cm) from water inlet
valve. For sink faucet, hot and cold water line.
Copper tubing with compression fitting for
specific faucet to be installed.
Drain: Separate drain P-traps for sink and
dishwasher.
DISHWASHER DRAIN
22-1/32"
(56.0 cm)
to bottom of
dishwasher
drain
1/2" (1.3 cm)
minimum
CABINET OPENING DIMENSIONS
*NOTE: The cutout must be
accurately cut to the dimensions
shown within 1/16" (1.6 mm).
Dishwasher top flange overlaps
the countertop cutout by 7/16"
(1.1 cm) on front and back edges
and 1/4" (6.4 mm) on sides.
• Cabinetry and countertop must
be sturdy enough to support
loaded dishwasher and sink
(400 lbs. [181.4 kg]).
Because Whirlpool Corporation policy includes a continuous commitment to improve our
products, we reserve the right to change materials and specifications without notice.
®
Briva
™
Dishwasher
OVERALL DIMENSIONS
water inlet
valve
5-25/32"
(14.7 cm)
back
If the dishwasher drain exits
wall
through the back wall, the
centerline of the drain must be
a minimum of 1/2" (1.3 cm)
below the dishwasher drain.
This is required to completely
drain the dishwasher tub so
that no standing water
remains in tub.
21-1/8"
(53.7 cm)
(see *NOTE)
42" model – 40" (101.6 cm)
A
36" model – 34" (86.4 cm)
It is recommended that sink
water and drain line
connections be located on
this side of cabinet.
It is recommended
that dishwasher water
and drain line
connections be
located on this side
of cabinet.
SIDE
factory
installed
1-3/4" (4.4 cm)
air gaps
to center of single
hole faucet
(20.3 cm)
dishwasher
9-7/16"
drain
(24.0 cm)
20-21/32" (52.5 cm)
(between clamp rails)
22" (55.9 cm)
42" model
36" model
for base cabinet
installations, min. 36"
(91.4 cm) width required
A
B
C
(see *NOTE)
A
25" (63.5 cm) deep
countertop
Countertop must be
level.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
FRONT
A
B
to center of single
hole faucet
8"
C
GFCI reset
center of
buttons
sink drain
5-1/2 ft. (1.7 m)
3-prong ground-type
power supply cord
18-5/16" (46.5 cm)
D
(between clamp rails)
A
B
40-1/2"
16-7/8"
9-9/16"
(102.9 cm)
(42.9 cm)
(24.3 cm)
34-1/2"
10-7/8"
6-9/16"
(87.6 cm)
(27.5 cm)
(16.6 cm)
backsplash
7/16" (1.1 cm) min.
flat surface required
21-1/8"
(53.7 cm)
(see *NOTE)
IMPORTANT: Corner radius dimensions
specified must be used. If they are not,
the dishwasher will not fit the opening.
radius: 2-1/4" (5.7 cm)
A
radius: 1" (2.5 cm) – the
B
right back corner must be
cut to this radius
C
Back right corner: If countertop is
more than 3/4" (1.9 cm) thick,
measure down 3/4" (1.9 cm) and cut
45° bevel all the way around radius.
3/4"
(1.9 cm)
19-3/8"
(49.2 cm)
maximum
opened lid
height
1-1/4"
(3.2 cm)
21"
(53.3 cm)
22-1/32"
(56.0 cm)
14" (35.6 cm)
C
D
39-11/16"
(100.8 cm)
33-11/16"
(85.6 cm)
45°
Ref. 8564766
12-06-04