KitchenAid KDTE104ESS3 Scheda tecnica - Pagina 9

Sfoglia online o scarica il pdf Scheda tecnica per Lavastoviglie KitchenAid KDTE104ESS3. KitchenAid KDTE104ESS3 12.

KitchenAid KDTE104ESS3 Scheda tecnica
Function
Problem
Causes
Code
Code
8-
2-
2. Debris stuck in
Draining
Drain Motor
drain motor
(cont.)
Electrical
impeller.
Problem
(cont.)
3. Open fuse on
control to drain
motor.
4. Drain Motor
Drive circuit on the
control.
3-
Drain Motor Drive
Drain
circuit on the
Stuck On
control.
9-
1-
1. Corroded or
Diverter
Can't Find
loose connection
Position
in diverter sensor/
motor circuit or
open/shorted
sensor/motor.
2. Mechanical
binding of diverter
shaft/disc.
3. Open fuse on
control to diverter
motor.
4. Diverter Motor
Drive circuit on the
control.
2-
Diverter Drive
Stuck On
Circuit on the
control.
3-
Control detected
Disk
diverter disk in
Missing
sump is missing.
10-
1-
1. Loose
Other
Dispenser
connection in
Electrical
Dispenser circuit
Problem
and/or open
dispenser
solenoid.
2. Open fuse on
control to
dispenser.
3. Dispenser Drive
circuit on the
control.
3-
1. Loose
Drying Fan
connection in fan
Error
circuit, and/or
open fan motor.
2. Fan drive circuit
on the control.
What to Check
1. Unplug dishwasher or disconnect
power.
2. Remove drain motor and
dislodge debris from impeller.
Refer to "Fuse Service Check" in
"Meter Check of Loads and Fuses"
section.
Unplug dishwasher or disconnect
power and replace control.
1. Unplug dishwasher or disconnect
power and replace control.
2. Inspect drain motor and
connections for overheating/
shorting. If evidence of overheating/
shorting exists, replace.
1. Check operation in Service
Diagnostics Cycle. Listen for cam
clicking as it rotates or inspect shaft
with mirror to see if rotating during
diverter interval. If rotating, it is
likely the sensor circuit.
2. Unplug dishwasher or disconnect
power and check connections in
Diverter Sensor and Motor circuit
with meter. Fix/replace open
connections/parts.
3. Inspect diverter sensor for
evidence of water or contaminants.
If yes, replace.
Check operation of diverter motor
during diagnostics. Inspect diverter
shaft with mirror. If motor appears
to be on (vibrates, hums), but you
see limited rotation, replace diverter
and seal.
Refer to "Fuse Service Check" in
"Meter Check of Loads and Fuses"
section.
Unplug dishwasher or disconnect
power and replace control.
1. Unplug dishwasher or disconnect
power and replace control.
2. Inspect diverter motor and
connections for overheating/
shorting. If evidence of overheating/
shorting exists, replace.
Remove lower spray arm, turbo
zone assembly, rear feed tube, and
outlet cover. Verify the round
diverter disk is installed.
Unplug dishwasher or disconnect
power and check resistances of
dispenser solenoid and all
connections in the Dispenser
circuit. Fix/replace open
connection/part.
Refer to "Fuse Service Check" in
"Meter Check of Loads and Fuses"
section.
Unplug dishwasher or disconnect
power and replace control.
Unplug dishwasher or disconnect
power and check resistances of fan
motor and all connections in the fan
circuit. Fix/replace open
connections or fan.
Unplug dishwasher or disconnect
power and replace control.

Troubleshooting Guide

NOTES:
For resistance checks, refer to "Dishwasher Strip Circuits" section.
For checking operation with diagnostics, refer to "Service Diagnostics
Cycle" section.
Customer
Potential Causes
Description
Clean LED Flashes Control programmed
with self diagnostics.
Won't Run or
1. No power to unit
Power Up ("Dead"
or bad connection.
Keypad/Console)
- No Operation
2. Loose connections
- No Keypad
in Power-up circuit or
response
between keypad(s)
- No LEDs or
and control.
Display
3. Model has an LCD
display and the
control has been
exchanged for one
that is not compatible
with the LCD display
module.
4. Control detected
door switch problem.
5. User interface
or control.
Won't Run and
1. By design, if the
LED for Start/
door is opened for
Resume Key Is
more than 5 seconds
Blinking Slowly
or power is
interrupted during a
cycle, the user must
press the Start/
Resume key to
resume operation.
2. Start/Resume key
not responding.
3. Control detected
door switch problem.
Won't Run and
Software or hardware
All LEDs On
incompatibility
problem with control.
Won't Start and
Control looks for door
Start/Resume Key
to open between
LED Flashes
cycles.
3 Times When
- Customer has not
Start/Resume Key
opened door since
Is Pressed
last cycle.
- Door switch
contacts stuck closed.
9
Check
Related
Error
Code
Read error code from the
dishwasher and refer to
"Service Error Codes"
table. Run service
Diagnostics Test cycle to
read full history of error
codes.
Check fuses, circuit
breakers, and junction box
connections.
1. Unplug dishwasher or
disconnect power.
2. Check continuity of
power connections to
control and connections
between keypad(s) and
control.
Unplug dishwasher or
disconnect power.
Verify correct control is
installed. Control should
have no 4-pin user
interface connector present
at P1B if it is configured for
an LCD model. Replace
control.
5-1
Refer to "Service Error
Codes" table.
1. Unplug dishwasher or
disconnect power.
Disassemble door and
inspect control power
connector (P4) and
adjacent PC board for
damage. Replace as
needed.
2. Refer to "Service Error
Codes" table for stuck key
(2-1). Run the diagnostic
check, Item (1).
- If drain motor turns on,
control is OK. Replace the
UI.
- If drain motor does not
turn on, replace control.
3. Inspect UI cable for
2-1
loose or damaged wiring.
Replace as needed.
4. Inspect UI assembly for
damage or contamination.
Replace UI as needed
Instruct customer. Refer to
Use and Care Guide.
See "One or More Keys
Won't Respond."
Refer to "Service Error
5-1
Codes" table.
1-2
Refer to "Service Error
Codes Table."
Refer to "Service Error
5-2
Codes" table.