ALIBI ALI-CD700VF Manuale di installazione rapida - Pagina 2
Sfoglia online o scarica il pdf Manuale di installazione rapida per Telecamera di sicurezza ALIBI ALI-CD700VF. ALIBI ALI-CD700VF 3. Ali-cd700 series infrared turret cameras
Stampa la pagina
3.
Drill a 3/4" hole for the drop cable, if necessary. The drop cable can be routed through the mounting
surface, or through a cable channel in the mounting plate.
4.
Route camera video and power extension cables between camera location and the monitoring
device (monitor, DVR, etc.).
5.
Remove the mounting plate from the camera assembly
Loosen the clip plate captive screw with the security L-wrench provided.
u
Slide the clip plate out as shown in the photo above.
v
Separate the mounting base from the enclosure.
6.
Anchor the mounting base to the ceiling with appropriate fasteners. If the camera drop cable will be
routed through a cable channel, make sure it is in place before securing the mounting plate to the
surface.
Cable channel (2)
7.
Connect the camera drop cable to video and power extension cables.
8.
Reattach the camera to the mounting plate.
Position the camera assembly onto the mounting plate such that the lip on the black ring
u
attached to the enclosure slips under the tabs on the mounting plate.
Mounting plate
Slide the clip plate out.
v
v
Mounting plate
Enclosure
Push the enclosure into the mounting plate until it is fully seated.
x Slide the clip plate in so that it catches the lip of the black ring on the encloser.
2
www.observint.com
u
Enclosure
Clip plate
v
Cable channel
u
Tabs
Clip Plate
x
y
y Tighten the clip plate screw until it is just snug.
9.
Connect the far end of the video extension cable to a monitoring device, such as a surveillance
monitor or digital video recorder (DVR).
10.
Connect the far end of the power extension cable to a power supply, then apply power to the
camera through the power extension cable.
11.
While observing video from the camera on a monitor, aim the camera at your surveillance target.
See the figure below for adjustment ranges.
0 ~ 3600
ALI-CD700VF series aiming the camera
For ALI-CD700VF series cameras only
12.
Use a screwdriver to adjust the ZOOM screw and the FOCUS screw until you produce the best image.
Specifications
Model
ALI-CD700, ALI-CD700G
Image Sensor:
1/3" DIS
Signal System:
NTSC
Effective Pixels:
976(H) × 496(V)
Min. Illumination:
0.1 lux @ (F1.2, AGC ON),
0 lux with IR
Shutter Time:
1/30 sec to 1/15,000 sec
Lens:
3.6 mm
Angle of view: 68.4°
Lens Mount:
M12
Adjustment Range:
Pan: 0 - 360°, Tilt: 0 - 75°,
Rotation: 0 - 360°
Day & Night:
IR cut filter with auto switch
Horizontal Resolution:
700 TVL
Synchronization:
Internal synchronization
Video Output:
1 Vp-p composite output (75 Ω / BNC)
S/N Ratio:
More than 62 dB
BLC:
ON
Operating Conditions:
-40 °F - 140 °F (-40 °C - 60 °C)
Humidity 90% or less (non-condensing)
Power Supply:
12 Vdc ± 10%
Power Consumption:
Max. 1.8 W (max. 4 W with IR cut filter on)
Weather Proof:
IP66
IR Range:
32 ~ 65 ft (10 ~ 20 m) approx.
Dimension:
3.53" × 2.33"
(89.6 × 59.1 mm)
Weight:
0.88 lbs (400 g)
0 ~ 900
0 ~ 750
ALI-CD700VF, ALI-CD700VFG
1/3" DIS
NTSC
976(H) × 496(V)
0.1 lux @ (F1.2, AGC ON), 0 lux with IR
0.14 lux @ (F1.4, AGC ON),0 lux with IR
1/60 sec to 1/100,000 sec
2.8 ~ 12 mm @ F1.4
Angle of view: 80° ~ 27.2°
φ14
Pan: 0 - 360°, Tilt: 0 - 90°,
Rotation: 0 - 360°
IR cut filter with auto switch
700 TVL
Internal synchronization
1 Vp-p composite output (75 Ω / BNC)
More than 62 dB
On
-40 °F - 140 °F (-40 °C - 60 °C)
Humidity 90% or less (non-condensing)
12 Vdc ± 10%
Max. 4 W (max. 5 W with IR cut filter on)
IP66
98 ~ 131 ft (30 ~ 40 m) approx.
5.28" × 4.88" × 3.47"
(134.2 × 123.9 × 88.1 mm)
1.76l lbs (800 g)
© 2014 Observint Technologies. All rights reserved.