ALIBI ALI-NS4023R Manuale di installazione rapida - Pagina 5
Sfoglia online o scarica il pdf Manuale di installazione rapida per Telecamera di sicurezza ALIBI ALI-NS4023R. ALIBI ALI-NS4023R 6. Ip bullet cameras
Anche per ALIBI ALI-NS4023R: Manuale di installazione rapida (5 pagine)
Stampa la pagina
Image Adjustment submenu (see above): Adjust the Saturation, Hue, Brightness,
—
Contrast and Sharpness of the video image. Each parameter can be set to a level of
0 ~ 100 either by moving the slider or entering the value in the box on the right. The
effect of the adjustment will appear in the Live View image in the menu.
3.
Open the other submenus on this screen. Adjust the following as needed. Refer to the Camera
Firmware User Manual for your camera for additional information about parameter settings.
Exposure Settings submenu: In this submenu, set the following for the best
—
performance:
Iris Mode: Select Auto or Manual. Some cameras may not offer both options.
Exposure Time: Value ranges from 1/3 to 1/100,000 s. The nominal value is 1/150.
Adjust it according to the lightening condition.
Gain: Set the gain to show the optimal brightness level.
Switch Day and Night: Select either Auto-Switch, Scheduled-Switch, or
—
Triggered by Alarm Input.
If using Auto-Switch, open the Day/Night Switch submenu to select the
Sensitivity, Filtering Time, and Smart IR feature ON or OFF.
If using Scheduled Switch, set the Start Time and End Time of the switch, then
open the Day/Night Switch submenu to select the Smart IR feature ON or OFF.
Also, click the Common, Day and Night tabs to set the Saturation, Hue, Brightness,
Contrast and Sharpness for Day and for Night modes.
Day/Night Switch submenu: You can set the Day/Night switch to Day, Night, Auto, or
—
Schedule. The option you select determines the submenu options.
Day or Night: These options both have one parameter: Smart IR.
Auto: If you select Auto switch, you can set the sensitivity (0 .. 7), filtering time and
Smart IR.
Schedule: Use Schedule to set that Start Time and End Time for the switch. Smart
IR is also selectable.
Backlight Settings: Backlight settings include BLC Area (Off, Up, Down Left Right
—
Center), the area to control, and WDR (Wide Dynamic Range) ON or OFF.
White Balance: White Balance selection is used to correct colors in the image
—
depending on the lighting source. You can also set the white balance manually (MWB),
using Automatic White Balance (AWB1), and lock the white balance setting (Locked WB).
Image Enhancement: Options in this submenu include Digital Noise Reduction (DNR)
—
ON or OFF. If ON, you can also adjust the level of noise reduction.
Video Adjustment: Video Adjustment includes:
—
Mirror: Mirror adjustment enables you to flip the image (Up/Down), flip Left/Right
(reflect or Center).
Rotate: Rotate rotates the image +90 degrees. Rotate and Mirror can be used to
adjust the image in any orientation.
Video Standard: Select 60 Hz for NTSC format.
Capture Mode: To make a complete use of the 16:9 aspect ratio, you can enable the
capture mode when you use the camera in a narrow view scene.
Other: Options in this menu depend on the features of the camera.
—
5
www.observint.com
Using the Waterproof Ethernet Fitting
Install the Waterproof Ethernet Fitting on the Ethernet cable end at the camera when moisture
or contamination exists in the area near the camera. The fitting includes several parts that must be
installed in a specific order. To install the fitting:
1.
Place the rubber O-ring over the camera drop cable end cap.
Push the O-ring up to the connector cap.
2.
Place the Lock Nut onto the network cable from the router
or switch as shown in the drawing to the right. The inside
threads must be toward the camera end.
3.
Place the rubber basket onto the network cable above the lock
nut as shown.
4.
Place the end cap onto the network cable above the rubber
gasket as shown. The fingered end must be toward the router
or switch.
5.
Install an RJ-45 connector onto the network cable.
6.
Plug the RJ-45 connector with the network cable into the
camera network drop cable.
7.
Fit the end cap on the network cable onto the camera drop
cable end cap. Rotate the network cable end cap to lock it in
place.
8.
Push the rubber gasket fully into the end of the network cable
end cap.
9.
Screw the lock nut onto the network cable end cap until it is
fully seated.
Network drop cable
from camera
Ethernet Fitting installed
Ethernet Fitting assembled and connected
© 2017, 2018 Observint Technologies. All rights reserved.
Network drop
cable from
camera
Drop cable
end cap
Rubber
O-ring
seal
RJ-45
connector
End cap
Rubber
gasket
Network cable from
router or switch
Lock nut
Network
cable
from
router or
switch