Makita 5143R Manuale di istruzioni - Pagina 9
Sfoglia online o scarica il pdf Manuale di istruzioni per Utensile elettrico Makita 5143R. Makita 5143R 13. Circular saw
Anche per Makita 5143R: Manuale di istruzioni (13 pagine), Manuale di istruzioni (13 pagine), Manuale di istruzioni (12 pagine), Manuale di istruzioni (16 pagine), Manuale di istruzioni (13 pagine)
Stampa la pagina
Riving knife adjustment
1
2
3
4
1- 5mm
1- 5mm
005397
Use the hex wrench to loosen the hex socket head bolt
for the riving knife adjustment, then raise the lower blade
guard. Move the riving knife up or down over the two
protuberances for settings indicated in the figure, so as
to obtain the proper clearance between the riving knife
and saw blade.
CAUTION:
Ensure that the riving knife is adjusted such that:
•
The distance between the riving knife and the
toothed rim of the saw blade is not more than 5
mm. The toothed rim does not extend more than 5
mm beyond the lower edge of the riving knife.
Switch action
005398
CAUTION:
Before plugging in the tool, always check to see
•
that the switch trigger actuates properly and
returns to the "OFF" position when released.
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
push in the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and
•
unplugged before carrying out any work on the
tool.
Removing or installing saw blade
The following blade can be used with this tool.
1. Setting
protuberances
2. Hex socket head
bolt (For
adjusting riving
knife)
3. Setting
protuberances
4. Cutting depth
1. Lock-off button
2. Switch trigger
1
2
Model
Max. dia.
Min. dia.
5603R
165 mm
150 mm
190 mm
170 mm
5703R,5705R
5903R
235 mm
210 mm
5103R
270 mm
260 mm
5143R
355 mm
350 mm
006481
The thickness of the riving knife is 1.8 mm for Models
5603R,5703R and 5705R or 2.0 mm for Models for
5903R and 5103R or 2.5 mm for Model 5143R.
CAUTION:
Do not use saw blades which do not comply with
•
the characteristics specified in these instructions.
Do not use saw blades the disc of which is thicker
•
or the set of which is smaller than the thickness of
the riving knife.
1
005399
CAUTION:
Be sure the blade is installed with teeth pointing up
•
at the front of the tool.
Use only the Makita wrench to install or remove the
•
blade.
Never depress the shaft lock while the saw is
•
running.
To remove the blade, press the shaft lock fully so that
the blade cannot revolve and use the hex wrench to
loosen the hex bolt counterclockwise. Then remove the
hex bolt, outer flange and blade.
To install the blade, follow the removal procedure in
reverse. BE SURE TO TIGHTEN THE HEX BOLT
CLOCKWISE SECURELY.
3
2
1
005400
When changing blade, make sure to also clean upper
and lower blade guards of accumulated sawdust. Such
9
Blade thickness
1.6 mm or less
1.9 mm or more
1.6 mm or less
1.9 mm or more
1.7 mm or less
2.1 mm or more
1.8 mm or less
2.2 mm or more
2.3 mm or less
2.7 mm or more
1. Hex wrench
2. Shaft lock
2
1. Hex socket head
bolt
2. Outer flange
3. Saw blade
4. Inner flange
4
Kerf