KitchenAid YKFEG500EBS Manuale di istruzioni per l'installazione - Pagina 3
Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Gamme KitchenAid YKFEG500EBS. KitchenAid YKFEG500EBS 16. Freestanding
Anche per KitchenAid YKFEG500EBS: Manuale di avvio rapido (2 pagine), Manuale d'uso (18 pagine)
Stampa la pagina
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools Needed
■
Tape measure
■
Flat-blade screwdriver
■
Phillips screwdriver
■
Level
■
Hand or electric drill
■
Wrench or pliers
■
Marker or pencil
Parts Supplied
Check that all parts are included.
■
10-32 hex nuts (attached to terminal block) (3)
■
Terminal lugs (3)
B
A. Anti-tip bracket
B. #12 x 1
■
Anti-tip bracket must be securely mounted to floor or wall.
Thickness of flooring may require longer screws to anchor
bracket to floor.
Parts Needed
If using a power supply cord kit:
■
A UL listed power supply cord kit marked for use with ranges.
The cord should be rated at 250 volts minimum, 40 amps or
50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm)
diameter connection opening and must end in ring terminals
or open-end spade terminals with upturned ends.
■
A UL listed strain relief.
Check local codes. Check existing electrical supply. See the
appropriate "Electrical Requirements" section.
It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
■
Masking tape
■
¼" drive ratchet
■
¼" nut driver
³⁄₈" and ⁵⁄₁₆" nut driver
■
¹⁄₈" (3.2 mm) drill bit (for
■
wood floors)
■
Tin snips or large wire
cutters (for cutting ground
strap if necessary)
A
⁵⁄₈
"
screws (2)
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
■
It is the installer's responsibility to comply with installation
clearances specified on the model/serial/rating plate. The
model/serial/rating plate is located on the frame behind a top
corner of the door or on either side of the drawer.
■
To eliminate the risk of burns or fire by reaching over heated
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
that projects horizontally a minimum of 5" (12.7 cm) beyond
the bottom of the cabinets.
■
Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
■
The anti-tip bracket must be installed. To install the anti-tip
bracket shipped with the range, see "Install Anti-Tip Bracket"
section.
■
Grounded electrical supply is required. See the appropriate
"Electrical Requirements" section.
IMPORTANT: To avoid damage to your cabinets, check with your
builder or cabinet supplier to make sure that the materials used
will not discolor, delaminate or sustain other damage. This oven
has been designed in accordance with the requirements of UL
and CSA International and complies with the maximum allowable
wood cabinet temperatures of 194°F (90°C).
Mobile Home - Additional Installation Requirements
The installation of this range must conform to the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280). When such standard is not
applicable, use the Standard for Manufactured Home
Installations, ANSI A225.1/NFPA 501A or local codes.
Mobile home installations require:
■
When this range is installed in a mobile home, it must be
secured according to the instructions in this document.
■
Four-wire power supply cord or cable must be used in a
mobile home installation. The appliance wiring will need to be
revised. See "Electrical Connection" section.
3