KitchenAid 3183659 Istruzioni per l'installazione - Pagina 2

Sfoglia online o scarica il pdf Istruzioni per l'installazione per Forno KitchenAid 3183659. KitchenAid 3183659 7. Electric built-in 24” and 27” thermal single and double ovens 24” and 27” thermal convection single and double ovens

Stampa la pagina
24" Thermal
Double oven
Before
you start...
Read the electrical and carpentry instructions.
Proper installation
is your responsibility.
A
qualified technician should install this oven. Make
sure you have everything
necessary for correct
installation.
It is the responsibility
of the installer to
comply with the installation clearances specified
on the serial/rating
plate. The serial/rating
plate
can be found behind the upper oven door on the
frame of the oven.
Check location
where the built-in oven will be
installed. The location should be away from strong
draft areas, such as windows, doors, and strong
heating vents. The built-in oven should be located
for convenient
use in the kitchen.
Cabinet opening dimensions
that are shown
must be used. Given dimensions
provide
minimum clearance. Contact surface must be
solid and level and flush with the bottom.
The recessed installation
area
must provide
complete enclosure around the recessed portion
of the oven.
ALL OPENINGS
IN THE WALL OR FLOOR
WHERE THE BUILT-IN OVEN IS TO BE
INSTALLED
MUST BE SEALED.
Electrical ground
is required. See "Electrical
requirements."
Do Not install single oven in a base cabinet
with a countertop above it.
2-l/2"
min.
oven console.
recessed
width
46-l 3/l 6'-
---I--
49-7/8" -
overall
height
See Note.'
'<
+L-'
\
)o Not',
eal oven
\
3 cabinets.
\
h"
min. overall
cabinet depth
cabinet
opening
height
i
I
Electrical
supply
junction
box
re
I
sed
Iht
NOTE:
The oven support surface must be flush
with the bottom of the cabinet cutout.
so upper 0vG
door, when
open, is 36"
from floor.
I
I
I
NOTE:
Clearances specified are for combustible
walls and materials that have a density of
20 or more pounds per cubic foot. No
evaluation has been made for installations
adjacent to materials that are less than
20
pounds per cu. ft. or to plastic tiles and
sheeting.
Important: Observe all governing codes
ordinances.
27" Thermal and Thermal
\
Convection
Double ovens
Electrical Shock Hazard
It is the customer's responsibility:
l
To contact a qualified electrical installer.
l
To assure that the electrical installation
is
adequate and in conformance with
National Electrical Code, ANSVNFPA 70-
latest edition**, and all local codes and
ordinances.
Failure to do so could result in fire,
electrical shock or other personal injury.
Personal Injury Hazard
Securely fasten oven to cabinet using the
screws provided (2 screws for a single
oven or 4 screws for a double oven).
Failure to do so could cause the oven to
move or tip during use and result in
personal injury.
*Note: There must be 1"
-mm.
between
bottom
ot
cabinet
door and top of
oven console.
2-l/2"
min.
-\Oven
control
R
console
I I I
cabinet
rL--
c
\
\
\
10 Not
\
:eal oven
\
o cabinets.
'
\
24" min. overal
cabinet
depth
I i
opening
49"
I
depth
cabinet
I
opening
eight
I
P'
lin.
I
I
I'
I Electrical
I surly
junction
43"
max. below
support
surface
.
!Ds
\
'.
IT + +
w
11" min.
Tools needed for
installation:
46-I 3/l 6"-
recessed
heigM
25-7/W' -
/OVerall
width
Parts supplied
for
installation:
recommended
so
upper oven door,
when open, is
36" from floor.
Panel A