KitchenAid KEBC206KWH03 Istruzioni per l'installazione - Pagina 3
Sfoglia online o scarica il pdf Istruzioni per l'installazione per Forno KitchenAid KEBC206KWH03. KitchenAid KEBC206KWH03 5. 30" electric built-in single and double ovens
Stampa la pagina
If codes permit
and a separate
grounding
wire is
used, it is recommended
that a qualified
electrician
determine
that the grounding
path and wire gauge
is in accordance
with local codes.
Do Not ground to a gas pipe.
Check with
a qualified
electrician
if you are not
sure oven is proper_y grounded.
Do Not have a fuse in the neutraJ or grounding
circuit.
Oven must be connected to the proper eUectricaU
voUtageand frequency as specified on the
modeU/sedaU rating pUate.(The modeU/sedaU rating
plate is located on the oven door or on the oven
frame.)
[_ Models rated from 7.3 to 9.6 kW at 240 volts
(5.5 to 7.2 kW at 208 volts} require a separate
@-ampere circuit. Models rated at 7.2 kW and
below at 240 volts (5.4 kW and below at 208
volts} require a separate 30-ampere circuit.
[_ A time-delay fuse or circuit breaker is
recommended.
[_ Connect directly to the fused disconnect (or
circuit breaker box} through flexible, armored
or non-metallic sheathed, copper cable (with
grounding wire}.
[_ Flexible armored cable from appliance should
be connected directly to junction box.
[_ Fuse both sides of the line.
[_ A U.L.qisted conduit connector must be
provided at the junction box.
[_ Do Not cut the conduit.
Wire sizes and connections must conform with the
rating of the appliance and to the requirements of
the National Electrical Code, ANSI/NFPA 70 -- latest
edition (% See Page 1) and all local codes and
ordinances.
if the house has aluminum wiring, follow the
procedure below.
a.) Connect the aluminum wiring to the copper
wire using special connectors designed and
Underwriters Laboratories-listed for joining
copper to aluminum. Follow the electrical
connector manufacturer's recommended
procedure.
b.) Aluminum/copper
connection must conform
with local codes and industry-accepted wiring
practice.
Use screws to attach
oven to cabinet.
Reattach
side
pieces.
Remove side
trim.
Remove
trim screws.
_
Grasp oven
frame to lift
oven.
t
Use screws to attach
oven to cabinet.
Reattach
side
_eces,
Remove side
trim,
shipping
feet,
Replace
oven
door.
Preparation
Excessive
Weight Hazard
Use two or more people to move and
install oven.
Failure to follow this instruction can
result in back or other injury.
Important:
Use both hands to remove oven
doors.
Do Not use handb or any portion
of the front
frame or trim for lifting.
Before moving oven across floor, check that oven
is on shipping base or sJide oven onto cardboard
or hardboard,
Do Not remove shipping feet at the front tower
corners of oven.
Remove
oven
door.
Remove
trim
screws,
Remove
oven
doors.
Replace
oven
doors.
{ateh
on the
hinge
in {ocked
position
=
door
free
to open
and
close
latch
on the
hinge
position
= door
ready
for
removal
_"
Remove trim screw,
Pull trim out,
'.TurnpowersuppUy
off. Move oven close to
final position.
, Remove and discard
shipping materials, tape
and protective film from
Do Not
the oven. Do Not
re
remove shipping base
shipping feet,
or shipping feet at the front Jower corners of
oven. The shipping feet will protect the Jower
oven trim unti_ oven is inserted into cabinet.
, Remove and set aside racks and other parts
from inside oven.
m Completely open oven door. In both back
corners of the door you will see door latches in the
locked position. Rotate both latches forward to the
unlocked position.
Grasp outside edges of door with both hands.
, Begin closing door, atthe moment the door
stops closing, lift and puii door toward you.
• Set door aside on a protective surface.
Pull top of trim
down,
3R
Remove trim screws attaching right and
left side trim to oven. Grasp the bottom end of
trim and pull away from oven. Slide top end of
trim downward to remove trim from oven. Take
care not to scratch other surfaces with ends of
trim. Set trim and screws aside on protected
surface.
Page 2