Garden Treasures Living BSH-A-SS Manuale - Pagina 10

Sfoglia online o scarica il pdf Manuale per Riscaldatore per patio Garden Treasures Living BSH-A-SS. Garden Treasures Living BSH-A-SS 13. Gas patio heater

Stampa la pagina

OPERATING INSTRUCTIONS

DANGER

• CARBON MONOXIDE HAZARD

• For outdoor use only. Never use inside

house, or other unventilated or enclosed

areas. This heater consumes air (oxygen). Do

not use in unventilated or enclosed areas to

avoid endangering your life.

Caution: Do not attempt to operate the heater until you have read and understand all Safety

Information in this manual and all assembly is complete and leak checks have been performed.

Before Turning Gas Supply ON:

1. Your heater was designed and approved for outdoor use only. Do NOT use it inside a building,

garage, or any other enclosed area.

2. Make sure surrounding areas are free of combustible materials, gasoline, and other flammable

vapors or liquids.

3. Ensure that there is no obstruction to air ventilation. Be sure all gas connections are tight and

there are no leaks.

4. Be sure the cylinder cover is clear of debris. Be sure any component removed during assembly or

servicing is replaced and fastened prior to starting.

Before Lighting:

1. Heater should be thoroughly inspected before each use, and by a qualified service person at least

annually. If relighting a hot heater, always wait at least 5 minutes.

2. Inspect the hose assembly for evidence of excessive abrasion, cuts, or wear. Suspected areas

should be leak tested. If the hose leaks, it must be replaced prior to operation. Only use the

replacement hose assembly specified by manufacturer.

Lighting:

Note: This heater is equipped with a pilot light that

allows for safer startups and shutdowns. Pilot must

be lit before main burner can be started.

1. Turn the control knob to the "OFF" position.

2. Fully open LP cylinder valve.

3. Push control knob in and rotate to pilot position.

Note: For initial start or after any cylinder change,

hold control knob in for 2 minutes to purge air from

gas lines before proceeding.

Igniter

Variable

control knob

OPERATING INSTRUCTIONS

Lighting (continued):

4. Push and release the igniter button until pilot flame is

visible through the glass tube.

5. Once the pilot is lit, continue to depress the control knob

for 30 seconds.

6. If the pilot does not stay lit, repeat steps 4 to 6.

7. If after repeating steps 4 to 6 unit does not light, then:

• Push in control knob and turn counterclockwise to

"Pilot".

• As you are depressing the control knob, place long

stem lighter through the glass tube to light the pilot.

• Repeat step 6.

8. Push in and turn the control knob to the "Hi", then

release control knob. If you want a lower temperature,

push in the control knob and turn counterclockwise to the

"LOW."

Note: If pilot fails to remain lit, all valves should be closed

and a waiting period of at least 5 minutes should pass

before attempting to light.

If you experience any ignition problem please consult

"Troubleshooting" on page 23.

Caution: Avoid inhaling fumes emitted from the heater's

first use. Smoke and odor from the burning

of oils used in manufacturing will appear. Both smoke and

odor will dissipate after approximately 30 minutes. The

heater should NOT produce thick black smoke.

Note: The burner may be noisy when initially turned on. To

eliminate excessive noise from the burner,

turn the control knob to the PILOT position. Then, turn the

knob to the level of heat desired.

Note: In normal conditions, the height of the flame is 2/3

the height of the glass tube when set in "Hi" position and

1/3 the height in "Low". The flame should be stable and

bright with no noise or black smoke. The opposite would be

abnormal conditions.

Igniter

Variable

control knob

Pilot

Normal

Abnormal

Low