KitchenAid KEHC379JWH3 Istruzioni per l'installazione - Pagina 3
Sfoglia online o scarica il pdf Istruzioni per l'installazione per Forno KitchenAid KEHC379JWH3. KitchenAid KEHC379JWH3 5. 27" and 30" electric built-in microwave/oven combination
Stampa la pagina
Electrical Shock Hazard
Electrically ground oven.
Connect ground with10-gauge-minimum
solid
copper w ire.
Failure t o
follow these instructions could result
in death, fire or electrical shock.
..................
,,,,,,,,
If codes permit and a separate grounding wire is
used, it is recommended that a qualified electrician
determine that the grounding path and wire gauge
are in accordance with local codes.
Do Not ground to a gas pipe.
Check with a qualified electrician if you are not
sure oven is propedy grounded,
Do Not have a fuse in the neutral or grounding
circuit,
Oven must be connected to the proper electrical
voltage and frequency as specified on the
model/serial rating plate. (The model/serial rating
plate is located on the oven door or on the oven
frame.)
[] CONNECTWITH COPPERWIRE ONLY,
[] Models rated from 7.3 to 9.6 kW at 240 volts
(5.5 to 7.2 kW at 208 volts) require a separate
40-ampere circuit, Models rated at 7.2 kW and
below at 240 volts (5.4 kW and below at 208
volts) require a separate 30-ampere circuit.
[] A time-delay fuse or circuit breaker is
recommended.
[]
[]
[]
[]
Connect directly to the fused disconnect (or
circuit breaker box) through flexible, armored
or non-metallic sheathed, copper cable (with
grounding wire),
Flexible armored cable from appliance should
be connected directly to junction box.
Fuse both sides of the line.
A U.L-listed conduit connector must be
provided at the junction box.
[] Do Not cut the conduit.
Wire sizes and connections must conform with
the rating of the appliance and to the
requirements of the National Electrical Code,
ANSI/NFPA 70 --latest
edition (% See Page 1)
and all local codes and ordinances.
D
Preparation
Excessive Weight Hazard
Usetwo or more people to move and install
oven.
Failure to follow this instruction can result in
back or other injury,
Important: Use both handsto remove oven
doors.
DONot use handle or any portion of the front
flame or trim for lifting.
Before moving oven acrossfloor, checkthat oven
is on shipping baseor slide oven onto cardboard
or hardboard.
Do Not remove shippingfeet at the front lower
comers of oven.
Do Not
_
remove
shipping
feet,
" Turn power supply off. Move oven
close to final position.
• Remove and discard shipping materials,
tape and protective film from the oven. Do
Not remove shipping base or shipping feet
at the front lower corners of oven. The
shippingfeet will protect the lower oven
trim until oven is inserted into cabinet.
• Remove and set aside racks and other parts
from inside oven.
D
Remove
side trim
pieces.
D
power
supply cable
shipping
foot
B
Graspoven frame
to lift oven.
(
)
D
Check oven and
microwave oven operation.
r_Use
screws to attach
oven to cabinet.
_
eattach side
trim pisces.
Remove
trim screws.
Remove
oven door,
D
Replace
oven door.
Insert small
end of pin
here.
Remove trim screw.
Ut,
Pulltop oftrim
down.
I
= Completely open lower oven door. Insert
small end of a door removal pin into each door
hinge. Grasp door handle from the bottom and
gently close door as far as it will shut. Lift slightly
and grasp bottom of door with other hand. Pull
door out at bottom to remove. Set door aside on
protected surface.
,. Remove trim screws attaching right and
left side trim to oven. Grasp the bottom end of
trim and pull away from oven. Slide top end of
trim downward to remove trim from oven. Take
care not to scratch other surfaces with ends of
trim. Set trim and screws aside on protected
surface.
Page 2