Gardena 11000 AS CLEAR Manuale dell'operatore - Pagina 5

Sfoglia online o scarica il pdf Manuale dell'operatore per Pompa dell'acqua Gardena 11000 AS CLEAR. Gardena 11000 AS CLEAR 17.

Stampa la pagina

Large hose diameter

GARDENA Connection System /

Art. 9036 / 9044: Medium hose

diameter

Small hose diameter

When using the largest hose diameter, the pump has the

maximum delivery capacity.

Pump

Art. 9034

Small hose

25 mm (1")

diameter

Art. GARDENA

Art. 7193

Hose Clamp

Medium hose

GARDENA Connection

diameter

System G 1"

Art. GARDENA

32 mm (1 1/4") *

Hose Clamp

Art. 7194

Large hose

38 mm (1 1/2")

diameter

Art. GARDENA

Art. 7195

Hose Clamp

When using the 38 mm (1 1/2") hose, we recommend the

GARDENA Flat Hose Set Art. 5005 with 10 m hose and

hose clamp.

* For Art. 9034 an additional connection nipple

1 1/4" hoses is supplied.

To connect the hose via the connection nipple:

1. When using the large diameter hose, cut off the con-

(4)

(a)

nection nipple

2. Only for Art. 9036 / 9044: When using the medium

hose diameter, cut off the connection nipple

3. Push the hose onto the connection nipple

4. Fix the hose to the connection nipple

a GARDENA Hose Clamp.

Connect hose via the GARDENA Connection System:

With 17000 AS CLEAR / 20000 AS DIRT (Art. 9036 / 9044)

the hose cannot be connected via the connection nipple

with the GARDENA Connection System.

3. OPERATION

DANGER! Risk of physical injury!

Injury when the product starts accidentally.

v Disconnect the product from the mains before

you connect, adjust or transport the product.

To pump water:

If the pump cannot be immersed via the handle, the pump

must always be immersed via a rope. Attach the rope

by pulling it through the eyelets provided and knotting

it. Minimum immersion depth during initial operation

see 7. TECHNICAL DATA.

(a)

Cut off nipple at

[ Fig. A2 ]

(b)

Cut off nipple at

[ Fig. A3 ]

Do not cut off nipple

[ Fig. A4 ]

Art. 9036

Art. 9044

32 mm (1 1/4")

Art. 7194

38 mm (1 1/2")

Art. 7195

51 mm (2")

Art. 7196

for

(4)

(b)

(4)

e.g. with

(4)

19 mm (3/4") / 15 mm (5/8") and 13 mm (1/2") hoses can

be connected via the GARDENA Connection System.

We do not recommend hose diameters smaller than

25 mm (1"), otherwise there will be a significant reduction

in the output of the delivery rate.

Hose diameter

Pump connection

13 mm (1/2")

GARDENA Pump Connection Set

15 mm (5/8")

GARDENA Pump Connection Set

19 mm (3/4")

GARDENA Pump Connection Set

1. Cut off the connection nipple

2. Connect the hose to the connection nipple

appropriate GARDENA Connection System.

To assemble the pump connection [ Fig. A5 ]:

DANGER! Risk of physical injury!

Injured cut by the impeller.

v Operate the pump only with the elbow con-

nector.

The hose can be easily connected and disconnected using

(2)

the locking devices

on the elbow connector

With Art. 9034 / 9036 a non-return valve is supplied which

prevents water from flowing back through the hose. The

max. delivery rate is only achieved without the non-return

valve.

If only a small amount of reflux is expected, e. g. if the hose

is laid flat, we recommend dispensing with the valve due to

the better delivery and suction performance.

1. Only for Art. 9034 / 9036: Insert the non-return valve

into the pump. Observe the installation direction.

2. Screw the elbow connector

until it stops. (If the hose is to be installed horizontally,

(1)

the elbow connector

to half a turn. When using the non-return valve,

increased force is required.)

3. Screw the connection piece

(4)

nipple

4. Push the connection nipple

(1)

elbow connector

until it stops until it engages audibly

and visibly.

The hose is securely connected to the pump.

Take care that the pump is located where the inlet open-

ings at the suction base are not obstructed neither com-

pletely nor partly.

Stand the pump on a brick if using in a pond.

If the suction process is close to the minimum water level

at start-up, the suction process may take longer.

1. Immerse the pump.

2. Connect the pump to the mains.

The sensor is initialised and indicated by a running light.

Art. 1750

Art. 1752

(4)

(b)

(4)

via the

(1)

clockwise into the pump

can be screwed out again up

(3)

into the connection

(4)

of the hose into the