Gardena 1265 Manuale dell'operatore - Pagina 5

Sfoglia online o scarica il pdf Manuale dell'operatore per Pompa dell'acqua Gardena 1265. Gardena 1265 12. Holiday watering set
Anche per Gardena 1265: Manuale di istruzioni per l'uso (20 pagine), Manuale di istruzioni per l'uso (17 pagine), Manuale dell'operatore (13 pagine)

Stampa la pagina

away from direct sunlight). Preferably place them

around 1 metre away. Bear in mind that a plant's water

requirements may change if its position is changed. If its

position is bright and warm, its water requirements will be

higher than in a cool, shady position.

CAUTION!

The plants must be positioned above the water

level of the reservoir to prevent the water from

the reservoir from flowing out via the supply pipes.

1. Group your plants in 3 groups according to their water

requirements.

2. Use planters or saucers so that any excess water will be

collected.

3. Allocate the individual drip distributors to the groups.

To connect the supply pipes to the pump

[ Fig. I1 / I2 ]:

The pump has 3 connections

(4)

1. Slide the sleeve

onto the supply pipe

(3)

2. Slide the supply pipe

(11)

tions

(4)

3. Screw the sleeve

onto the connection

4. If you do not use all 3 drip distributors, screw the end

(5)

caps

onto the unused connections

4. OPERATION

DANGER! Risk of injury!

Risk of injury when the product starts

accidentally.

v Disconnect the product from the mains before

you fill the container.

To start the watering [ Fig. O1 ]:

CAUTION!

Damage to the pump if it runs dry.

v Make sure that the container is always

sufficiently filled with water.

5. MAINTENANCE

DANGER! Risk of injury!

Risk of injury when the product starts

accidentally.

v Disconnect the product from the mains before

you maintain the product.

(11)

(3)

for supply pipes

(3)

onto one of the three connec-

(11)

Connecting the drip distributors to the supply pipes

[ Fig. I3 ]:

1. Cut the supply pipe perpendicular to its length

position where you are setting up the drip distributor

(4)

2. Slide the sleeve

onto the supply pipe

(3)

3. Push the supply pipe

(6)

distributor

until it reaches the stop.

4. Screw the threaded collar

(6)

drip distributor

Connecting the drip pipe to the drip distributor

[ Fig. I4 ]:

(8)

1. Cut the drip pipe

perpendicular to its length.

(8)

2. Push the drip pipe

onto the connection on the drip

(6)

distributor

until it reaches the stop.

(8)

3. Cut the drip pipe

at an angle at the position where

you want to water.

This ensures that the water will drip more efficiently.

4. Close unused connections of the drip distributor

(7)

the plugs

Fitting the drip pipe to the pipe peg [ Fig. I5 ]:

(9)

1. Place the pipe peg

into the soil of the plant at the

desired position.

(8)

2. Clip the drip pipe

into one of the 3 holding fixtures on

(9)

the pipe peg

in such a way that the drip pipe is facing

downwards.

If a plant has higher water requirements, several drip pipes

can be fitted to a hose bracket.

1. Fill the container with the previously calculated

amount of water (make sure that the container

stands in a secure position).

2. Place the pump in the container filled with water

(make sure that the pump is level with the bottom of

the container).

(2)

3. Connect the pump

to the power adapter

4. Plug the power adapter

The watering will start for 1 minute and the control

(Lc)

indicator

will illuminate green.

5. During the first watering, check all connections for leaks.

The watering will be repeated daily at the same time as the

power adapter was plugged in.

To clean the pump:

DANGER! Risk of injury!

Risk of injury and risk of damage to the

product.

v Do not clean the product with a water jet

(in particular high-pressure water jet).

v Do not clean with chemicals including petrol or

solvents. Some can destroy critical plastic parts.

(3)

at the

(3)

onto the connection on the drip

(4)

onto the connection on the

(6)

(1)

into an electrical socket.

(6)

with