KitchenAid YRBS275PDB5 Manuale di istruzioni per l'installazione - Pagina 4
Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Forno KitchenAid YRBS275PDB5. KitchenAid YRBS275PDB5 11. 27" electric built-in single and double ovens
Stampa la pagina
Electricalconnection
Electrical Shock Hazard
Disconnect power to the junction box before
making connection.
Electrically ground oven.
Connect ground with 10-gauge-minimum solid
copper wire.
Failure to follow these instructions could result
in death, fire or electrical shock.
This oven is manufactured with white {neutral)
power supply wire and a cabinet-connected bare
grounding wire twisted together.
Feed oven cable through opening in
[] the cabinet. Make electrical connection
following the steps needed for your installation.
1. Disconnect the power supply.
2. Remove the junction box cover.
3. Connect oven cable to junction box through the
U.L-listed conduit connector.
4. Connect the two black wires together with
twist-on connectors.
5. Connect the two red wires together with
twist-on connectors.
6. Complete electrical connection according to
local codes and ordinances.
cable from power
supply
junction
box
wire
white
grounding
oven
U.L.-listed
cable wires i
"_ conduit
factory
crimped
cable from
connector
Figure 1
oven
if local codes PERMIT
connecting cabinet-
grounding conductor to
neutral white wire in
junction box:
7. Connect the factory-crimped
bare and white oven cable wires
to the neutral (white) wire in
junction box. See Figure 1.
8. Replace junction box cover.
cable from power supply
junction
box
_
red
__
white
W_
reS
Y
-"m___
_ black wires
bare grounding
_
J
....
wires
_
_
U.L.-listed
conduit
Figure 2
cable from
connector
oven
if local codes DO NOT
PERMIT connecting
cabinet-grounding
conductor
to neutral
white
wire
in
junction box:
7. Separate the factory-
crimped bare and white
oven cable wires.
8. Connect white oven
cable wire to neutral
(white) wire in junction
box. See Figure 2.
9. Connect the bare
grounding oven cable
wire to a grounded wire
in the junction box. See
Figure 2.
10. Replace junction box
cover.
if connecting to a
four-wire electrical
system:
7. Separate bare and white
oven cable wires.
8. Connect white oven cable
wire to neutral (white) wire
in junction box. See
Figure 2.
9. Connect the bare
grounding oven cable wire
to the green grounding
wire in junction box. Do
Not connect bare
grounding wire to neutral
(white) wire in junction
box. See Figure 2.
10. Replace junction box
cover.
Attachment
Carefully push against seal area of oven
front frame when pushing oven into
cabinet.
Do Not push against outside edges.
_ Lift oven into
cabinet cutout usin(
oven opening as an area
to grip.
shipping
foot
Push against seal area of front frame to
push oven into cabinet until shipping feet
almost contact cabinet. Use a Phillips
screwdriver to remove screws attaching
shipping feet. Remove and discard shipping
feet.
Push oven completely into cabinet and
center oven in cabinet cutout.
!4 screws
[] Important: Securely fasten oven to
cabinet using the screws provided (two
screws for a single oven or four screws for a
double oven). Insert the screws through holes
in mounting rails. Do Not overtighten screws.
Slide top
of trim up.
_
!
Pushtrim
22_
_
into place.
Replace
trim screw.
[] Replace oven racks.
oven frame
hinge slot
_door
hinge
Replace the single or upper oven door by
[]
inserting ends of hinges into hinge slots in
oven frame. Push behind each hinge so that hinges
are pushed into oven frame as far as they will go.
Open door and remove both door removal pins.
Close and open door to check that door closes and
opens completely, if door does not close or open
completely, you have not pushed hinges
completely intoframe. Repeat door removal step
and reinsert door into hinge slots again.
Repeat for lower oven door.
[] Slide top end of each trim upward onto
oven side rails. Push each trim into place at
bottom of trim. Use screws to attach each trim
to oven. Take care not to scratch other
surfaces with ends of trim.
Check operation
O[]
Turn on power supply. The
display panel will light up briefly. "PF"
should appear in the temperature display.
/
'if
i
.... i
BAKE il BROIL
CLEAN!
<
J
k
J
k
_'!
[]
Check the operation of your single oven.
Press the "BROIL" pad. "BROIL" will appear
in the display. Press the "START" pad.
Page 3
Make sure the oven door is closed and the
"ON" light is shown in the display area. After
2 minutes, partially open oven door. You
should feel heat from the oven. Press the
"CANCEL" pad.
Check the operation of your double oven.
Press the "Upper Oven" pad. Press the
"BROIL" pad. "BROIL" will appear in the
display. Press the "START" pad. Make sure
the oven door is closed and the "ON" light is
shown in the display area. After 2 minutes,
partially open oven door. You should feel heat
from the oven. Press the "CANCEL" pad.
Press the "Lower Oven" pad and repeat the
steps you completed for checking the upper
oven.
If your oven does not heat or an "F", followed by
a number, appears in the display, contact your
dealer or check the
"if you need service..." section of this Installation
Instructions.
To get the most efficient use
from your new oven, read your
Use and Care Guide. Keep
Installation
Instructions
and Guide close to oven
for easy reference.