Gardena FSP 5500 7868 Manuale di istruzioni per l'uso - Pagina 4
Sfoglia online o scarica il pdf Manuale di istruzioni per l'uso per Pompa dell'acqua Gardena FSP 5500 7868. Gardena FSP 5500 7868 6. Submersible pump for pond filter or stream
Stampa la pagina
G
pump checked by our GARDENA Service Centre or by an
authorised electrician.
Check line voltage
Check line voltage. Data indicated on the type plate must match
technical data of the mains supply.
Do not operate pump
The pump must not be operated when there are people in the
when there are people
water.
in the water
Swimming pools
Swimming pools and garden ponds should be designed accord-
and garden ponds
ing to international and national design regulations. Please
consult a professional electrician.
Do not use power cable
Do not use the power cable to carry the pump or to pull the plug
to carry the pump
out of the socket. Protect the power cable from heat, oil and
sharp edges.
Disconnect plug
Please unplug the pump after operation and before carrying out
any maintenance works.
Temperature of the liquid
The temperature of the liquid used must not be below 4 °C or
used
above 35 °C.
Wear and reduced
Sand and other abrasive substances in the liquid cause in-
output
creased wear and reduce the output of the pump.
Observe local noise
Please observe the local noise prevention regulations.
prevention regulations
Operation
The universal fitting provides you with various possibilities
G 3 /4
to fit a hose:
➔ Connection via graduated nipple of
1"
25 mm (1")- or
.
32 mm (5 /4")- or
.
G 1
38 mm (1 1/ 2 ")- hoses
.
➔ Connection via GARDENA Water hose-Plug-in-system
5 /4"
fittings of
13 mm (1/ 2 ")- or
.
1 1/ 2 "
16 mm (5 / 8 ")- or
.
19 mm (3 /4")- hoses
.
Recommendation :
Fix 38 mm (1 1/ 2 ")-, 32 mm (5 /4")- and 25 mm (1")-hoses
additionally with a hose clip.
Cut off the parts of the universal fitting that you do not need
with a saw.
10
Fitting the universal
1. Push the sleeve nut over the universal connector.
connector
2. Place the sealing ring in the sleeve nut.
3. Screw the universal adapter and sleeve nut onto the pressure
joints of the pump.
Positioning the pump
Position the pump on a firm base so that it is at least 20 cm
immersed in water.
Pay attention to
Please note the maximum submersion depth (see "Technical Data").
minimum water depth
Starting the pump
Connect the power cable to a 230 V AC socket.
Caution! Pump will start running immediately!
A
Avoid dry operation
Avoid dry operation of the pump as dry running will produce
undesirable heat and destroy the pump.
System Extensions – Product Recommendations
Operating an external filter
To clean your pond you can connect an external filter such as the
GARDENA Pond Filter
GARDENA Pond Filter with UVC-light
For this purpose use a hose in order to connect the Pump
for Filters and Streams with the external filter.
Please observe the information on safety in the relevant
A
operating instructions!
Operating a stream
The pump has been designed for streams and waterfalls:
Large streams and waterfalls
.
➔ Connect a 38 mm (1 1/ 2 ") GARDENA Pond Hose,
Art. No. 7898, and run it to the source of your stream.
Smaller streams
.
➔ Connect hoses with a smaller diameter correspondingly e.g.:
32 mm (5 /4")-GARDENA Pond Hose, Art. No. 7897
25 mm (1")-GARDENA Pond Hose, Art. No. 7896.
Care Instructions
Cleaning the pump
If you use your pump frequently in dirty water you should clean
your pump as follows:
1. Remove the mains plug.
2. Take the pump out of the water.
3. Rinse the housing of the pump thoroughly with water.
If necessary, also direct the water into the pressure outlet.
4. Put the pump back into your pond or stream.
Information: Do not use any hard objects or strong detergents!
G
Art. No. 7904
Art. No. 7905
11