Gardena 14770 Manuale dell'operatore - Pagina 7

Sfoglia online o scarica il pdf Manuale dell'operatore per Attrezzature per prato e giardino Gardena 14770. Gardena 14770 12. Battery pole pruner

Stampa la pagina

1. Widen the belt clip

(4)

, clamp it around the tube and tighten it with the

(5)

screw

(6)

2. Hook the carabiner

onto the belt clip

3. Adjust the shoulder strap to the desired length with the quick release

fastener.

3. OPERATION

DANGER! Risk of injury!

Cut injury when the product starts accidentally.

v Wait for the chain to stop, remove the battery and slide the

protective cover over the bar before you adjust or transport

the product.

To charge the battery [ Fig. O1 / O2 / O3 ]:

CAUTION!

v Note the mains voltage! The voltage of the power source must

match the voltage specified on the rating plate of the charger.

For the GARDENA Pole Pruner Art. 14770-55 there is no battery

and no charger in the scope of delivery.

Thanks to the intelligent charging process, the charge condition of the

battery is automatically detected and then charged up with the optimal

charge current depending on battery temperature and voltage.

In this way, the battery is treated with care and remains permanently fully

charged when it is stored in the charger.

1. Push the locking button

(A)

and remove the battery

(D)

holder

(C)

2. Connect the battery charger

(C)

3. Slide the battery charger

onto the battery

When the battery charge indicator

the battery is being charged.

When the battery charge indicator

permanently green the battery is completely charged

(Charging time, see 7. TECHNICAL DATA).

4. Examine the charge status regularly while you charge.

5. When the battery

(B)

is completely charged, you can disconnect the

(B)

(C)

battery

from the charger

Meaning of the indication elements:

Indication on the charger [ Fig. O3 ]:

Flashing of the battery

The charging procedure is indicated by flashing of the battery charge

(Lc)

charge indicator

indicator

Note: The charging procedure is only possible when the battery

temperature is within the allowable charging temperature range,

see 7. TECHNICAL DATA.

Continuous lighting

Continuous lighting of the battery charge indicator

of the battery

the battery is fully charged or that the temperature of the battery is

(Lc)

charge indicator

not within the allowable charging temperature range and can therefore

not be charged.

When the battery is not inserted, continuous lighting of the battery

(Lc)

charge indicator

socket outlet and that the battery charger is ready for operation.

Battery charge status indication

After starting the product, the battery charge status indication

is displayed for 5 seconds.

Battery charge status

67 – 100 % charged

34 – 66 % charged

11 – 33 % charged

0 – 10 % charged

If the LED

(L1)

flashes green, the battery must be charged.

If the error LED

(Wp)

is illuminated or flashing, see 6. TROUBLESHOOTING.

To fill in chain oil [ Fig. O5 ]:

DANGER!

Physical injury due to chain breakage when the chain on

the bar is not sufficiently lubricated.

v Check whether sufficient quantities of chain oil are delivered

prior to each use.

(4)

(B)

from the battery

into a mains socket.

(B)

(Lc)

at the charger flashes green

(Lc)

at the charger illuminates

(Lc)

indicates that

indicates that the mains plug is inserted in the

(P)

on the product [ Fig. O4 / O14 ]:

Battery charge status indication

(L1)

(L2)

(L3)

and

illuminate green

(L1)

and

(L2)

illuminate green

(L1)

illuminates green

(L1)

flashes green

We recommend to use GARDENA Chain Saw Oil Art. 6006 or an

equivalent mineral chain oil from a specialist supplier.

(7)

1. Unscrew the lid

of the oil tank.

2. Fill chain oil into the filler neck

completely filled with oil.

(7)

3. Close the lid

of the oil tank again.

4. Check the oil lubrication system.

The device must be cleaned thoroughly if oil has been spilled.

To check the oil lubrication system [ Fig. O6 ]:

(20)

v Point the bar

at a bright wood cutting surface at a distance of

approx. 20 cm.

After operating the machine for one minute, clear traces of oil must be

visible on the surface.

CAUTION!

Never let the bar

(20)

come into contact with sand or soil as this

will lead to increased wear of the chain.

Work positions:

The Pole Pruner can be operated in 2 working positions (above / below).

To ensure a tidy cutting edge, thick branches should be cut in 2 steps

(Illustrations similar).

Saw above (thick branches) [ Fig. O6 /O7 /O8 ]:

1. Saw the branch from below max. 1/3 of the diameter (the chain slides

(a)

to the front stop

2. Saw off the branch from above (the chain pulls to the rear stop

Saw below [ Fig. O6 /O9 ]:

v Saw off the branch from above (the chain pulls to the rear stop

To tilt the motor unit [ Fig. O10 ]:

(1)

The motor unit

can be tilted in 15° increments from 60° to – 60°.

1. Keep both orange buttons

desired direction.

2. Release both orange buttons

To extend the telescopic tube [ Fig. O11 ]:

The telescopic tube

(2)

can be continuously extended by up to 50 cm.

1. Loosen the orange nut

2. Extend the telescopic tube

3. Tighten the orange nut

To start the pole pruner [ Fig. O1 /O12 /O13 /O14 ]:

DANGER! Risk of injury!

Risk of injury if the product does not stop when you

release the start lever.

v Do not bypass the safety devices or switches. For example do

not attach the start lever to the handle.

Verify that the following conditions are met before commencing

work:

– The tank has been filled with sufficient chain oil and the lubrica-

(P)

tion system has been checked (see 3. OPERATION).

– The chain is tensioned (see 4. MAINTENANCE).

To start:

The product is provided with a two-switch safety device (start lever

with starting lockout) to prevent the product from being turned on

by accident.

1. Put the battery

(B)

into the battery holder

2. Open the snap fit

(13)

3. Hold the pole pruner with one hand on the insulated gripping surface

on the telescopic tube

4. Slide the starting lockout

The pole pruner starts and the battery charge status indication

displayed for 5 seconds.

5. Release the starting lockout

To stop:

1. Release the start lever

The pole pruner stops.

(8)

until the viewing window

(11)

pushed and tilt the motor unit

(11)

and let the motor unit

(12)

(2)

to the desired length.

(12)

again.

(D)

until it audibly engages.

of the protective cover and remove from the bar.

(2)

and with the other hand on the handle

(15)

forward and pull the start lever

(15)

(16)

(9)

(b)

(1)

in the

(1)

engage.

(14)

(16)

(P)