KitchenAid KBMC147HBT05 Istruzioni per l'installazione - Pagina 3

Sfoglia online o scarica il pdf Istruzioni per l'installazione per Forno a microonde KitchenAid KBMC147HBT05. KitchenAid KBMC147HBT05 5. 27" and 30" microwave oven
Anche per KitchenAid KBMC147HBT05: Manuale delle parti (9 pagine)

KitchenAid KBMC147HBT05 Istruzioni per l'installazione
Electrical 8hockHazard
Electrically ground
oven.
Connect ground with 12-gauge-minimum
solid copper wire.
Failure to follow these instructions can resutt
in death, fire or eleotrioal shock.
ff codes permit
and a separate
grounding
wire
is used, it is recommended
that a qualified
electrician
determine
that the grounding
path
and wire gauge are in accordance
with
_ocaJ
codes.
Do Not ground to a gas pipe.
Check with a quaiified electrician if you are not
sure oven is property grounded.
Do Not have a fuse in the neutraJ or grounding
circuit.
Oven must be connected to the proper
electrical voltage and frequency as specified on
the model/serial rating plate. (The model/serial
rating plate is located on the oven door or on
the oven frame.}
CONNECT WiTH COPPERWiRE ONLY.
D A four-wire or three-wire, single phase,
240-volt, 60 Hz, AC°only electrical supply is
required on a separate, 20-ampere circuit,
fused on both sides of the line.
Note: Models KBHCl09, KBHC179,
YKBHC109 and YKBCH179 require a 30-
ampere circuit.
D A time-delay fuse or circuit breaker is
recommended.
D Connect directly to the fused disconnect (or
circuit breaker box} through flexible,
armored or non-metallic sheathed, copper
cable (with grounding wire}.
Flexible armored cable from appliance
should be connected directly to junction
box.
D Fuse both sides of the line,
D A U.L.qisted conduit connector must be
provided at the junction box.
D Do Not cut the conduit.
Wire sizes and connections must conform with
the rating of the appliance and to the
requirements of the National Electrical Code,
ANSI/NFPA 70 --latest
edition (% See Page 1},
or CSA Standards C22.11-94, Canadian
Electrical Code, Part ] and C22.2 No. 0°M91 -
latest edition (:_ See Page 1} and ail local
codes and ordinances.
Preparation
Do Not remove shipping feet at the front tower
corners of oven.
remove
shipping
feet.
m Turn power supply off.
. Remove and discard shipping
materials,
tape
and protective
film from the oven.
Do Not
remove shipping
feet at the front lower
corners of oven.
The shipping
feet wHI
protect
the Jower oven trim unti_ oven is
inserted
into cabinet.
. Remove and set aside racks and other parts
from inside oven.
2m
Completely open microwave oven door.
Remove
trim
screw.
Smide top of trim
downward
and
remove.
3u
Remove trim screws attaching
right
and left side trim to oven. Grasp the bottom
end of trim and pull away from oven. Slide top
end of trim downward
to remove trim from
oven. Take care not to scratch other surfaces
with ends of trim. Set trim and screws aside
on protected
surface.
installation
Excessive Weight Hazard
Use two or more people to move and install
oven,
Failure to follow this instruction can result
in back or other injury.
Do Not use handJeor any portion of the front
frame or trim for tifting.
Lift microwave oven partially into
cabinet cutout. Feed power supply cane from
microwave oven through hob in cutout
bottom. If using recessed junction box on
rear wall, complete electrical connection now.
(See section C, Electrical Connection}.
2 screws
5_
Important: Securely fasten oven to
cabinet using the two screws provided, insert
the screws through holes in mounting rails. Do
Not overtighten screws.
6m
Slidetop end of each trim upward onto
oven side rails. Push each trim into place at
bottom of trim. Use screws to attach each trim
to oven. Take care not to scratch other
surfaces with ends of trim.
7u
Replace oven racks.
Carefully
push against the front of the
microwave
oven to push oven into cabinet
until shipping
feet almost
contact cabinet.
Use
a Phillips screwdriver
to remove screws
attaching
shipping
feet. Remove and discard
shipping
feet.
Push oven completely
into cabinet and center
oven in cabinet cutout.
Page 2