KitchenAid KHHC2090SBL3 Manuale di istruzioni per l'installazione - Pagina 7

Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Forno a microonde KitchenAid KHHC2090SBL3. KitchenAid KHHC2090SBL3 12. Microwave hood combination

Stampa la pagina

The microwave

oven must be installed on a minimum

of 1 wall

stud, preferably 2, using a minimum

of 1 lag screw, preferably 2.

Using measuring

tape, find and clearly mark the vertical

centerline

of the opening.

}L___o

A. Centerline

2. Align the centerline of the wall template with the centerline on

the wall, making sure it is level, and that the top of the wall

template abuts the bottom edge of the upper cabinet. Tape

the wall template into place.

NOTES:

•

If the front edge of the upper cabinet is lower than the back

edge, lower the wall template so that its top is level with the

front edge of the cabinet.

•

If the wall template is damaged or unusable, measure and

mark the wall with the dimensions described in Step 4.

.ll

................................................................

A. Rear wall

B. Wall template

C. Top of wall template must align with

front edge of cabineL

D. Front edge of upper cabinet

3. Mark both end holes of the mounting plate through the wall

template.

4. Remove the wall template and check the markings:

Upper cabinet bottom

151/2.

Centerline

18%6"

(39.4 crn)

(46.5 crn)

14V8"

14Va"

J-

(3 .9

om)-- l

//2._.2 .............................

L............................

'....... 2 .........

Bottom of mounting plate

Mounting plate end hole

The bottom edge line must be 18sAe '' (46.5 cm) from the

bottom of the upper cabinet, and must be level.

The end holes must be 151/2 '' (39.4 cm) from the bottom

edge of the upper cabinet, and must be on a level line with

each other. They must each be 141/8 '' (35.9 cm) from the

centerline.

With the support tabs facing forward (see illustrations in

"Locate Wall Stud(s)" section), align the mounting plate center

markers to the centerline on the wall, making sure its bottom

edge is aligned to the horizontal line drawn in Step 3, and that

the end holes are properly marked. Make sure the mounting

plate is level.

Holding the mounting plate in place, find the wall stud

centerline(s) drawn in Step 2 of "Locate Wall Stud(s)," and

mark at least 1, preferably 2 hole(s) through the mounting

plate, closest to the wall stud centerline(s). See figures 1, 2

and/or 3 in "Possible Wall Stud Configurations"

in "Locate

Wall Stud(s)" section. The blackened holes in the shaded

areas are ideal hole locations.

7. Set the mounting plate aside.

Wall Venting Installation

Only

Upper cabinet bottom

_ %" (1 cm)

10.

11.

12.

13.

14.

4" (10.2 cm)

CenterJine

* I

6" (15.2 era)

Mark the centerline 3/8" (1 cm) down from the bottom edge of

the upper cabinet.

Using measuring tape, measure out 6" (15.2 cm) on both sides

of the centerline, and mark.

Measure down 4" (10.2 cm) from the mark made in Step 8,

and mark.

Using a straightedge, draw the 2 horizontal, level lines through

the marks made in steps 8 and 10.

Draw the 2 vertical, plumb lines down from the marks made in

Step 9 to complete the 12" x 4" (30.5 x 10.2 cm) rectangle.

This is the venting cutout area.

Cut a 3/4" (19 mm) hole in one corner of the cutout area.

Using a keyhole saw, cut out the venting cutout area.

In addition to being installed on at least 1 wall stud, the mounting

plate must attach to the wall at both end holes. If the end holes

are not over wall studs, use two 1/4-20 x 3" round-head bolts with

toggle nuts; if 1 end hole is over a wall stud, use 1 lag screw and

one 1/4-20 x 3" round-head bolt with toggle nut; or if both end

holes are over wall studs, use 2 lag screws. Following are

3 installation configurations.

Installation for No Wall Studs at End Holes

(Figures I and 2)

Drill 3/4" (19 mm) holes through the wall at both end holes

marked in Step 3 of "Mark Rear Wall."

Drill 3/16" (5 mm) hole(s) into the wall stud(s) at the hole(s)

marked in Step 6 of "Mark Rear Wall." Refer to figures 1 and 2

in "Possible Wall Stud Configurations"

in "Locate Wall Stud(s)"

section.

Installation for Wall Stud at One End Hole (Figure 3)

1. Drill a 3/16" (5 mm) hole into the wall stud at the end hole

marked in Step 3 of "Mark Rear Wall."

2. If installing on a second wall stud, drill a 3/16" (5 mm) hole into

the wall stud at the other hole marked in Step 6 of "Mark Rear

Wall." Refer to Figure 3 in "Possible Wall Stud Configurations"

in "Locate Wall Stud(s)" section.

3. Drill a 3/4" (19 mm) hole through the wall at the other end hole.

Installation for Wall Studs at Both End Holes (Figure 4)

1. Drill 3/16" (5 mm) holes into the studs at the end holes marked

in Step 3 of "Mark Rear Wall."