Garmin echoMAP 50s Guide Riferimento - Pagina 30

Sfoglia online o scarica il pdf Riferimento per Attrezzatura marina Garmin echoMAP 50s Guide. Garmin echoMAP 50s Guide 42. Technical reference for garmin nmea 2000 products
Anche per Garmin echoMAP 50s Guide: Manuale di istruzioni per l'installazione (12 pagine), Manuale di riferimento (2 pagine), Manuale d'uso (28 pagine), Informazioni sul prodotto (37 pagine), Manuale di istruzioni (28 pagine), Modello (2 pagine), Dichiarazione di conformità (6 pagine), Manuale di configurazione (2 pagine), Manuale di avvio rapido (4 pagine), Manuale di istruzioni per l'installazione (8 pagine), Manuale d'uso (38 pagine)

Stampa la pagina
Garmin echoMAP 50s Guide Riferimento
NMEA 2000-Certified Sensor Configuration Information

GRA 10 (Garmin Rudder Angle Adapter)

Note: This section provides specific configuration information for the GRA 10 adapter using your compatible Garmin display device. To
access the NMEA 2000 configuration menu on your display device, consult the documentation provided with your display device.
Calibrating the Rudder Angle
To use the GRA 10 adapter, you must calibrate the angle of the rudder that the adapter is associated with.
1. Turn the boat ignition key to the On position (not Start).
2. From the NMEA 2000 Devices list, select the GRA 10 device.
3. Select an option:
• For most Garmin chartplotters, select
• For other Garmin marine devices, select
4. Follow the on-screen instructions to calibrate the starboard and port rudder angles.
5. Select
OK
when the calibration is complete.
Troubleshooting the Gauge Type
When connected to a gauge, the GRA 10 adapter gauge type is set to auto Detect by default, and the adapter automatically detects the type of
gauge it is connected to. If the rudder-angle reading on a connected Garmin chartplotter or marine instrument changes with the engine RPM, the
adapter may be detecting the wrong type of gauge.
To test the gauge-type setting:
1. When the boat is not moving, put the engine in neutral.
2. Use the throttle to increase the engine RPM. If the rudder-angle reading changes with the engine RPM, change the gauge type.
To change the gauge type:
1. From the NMEA 2000 Devices list, select the GRA 10 device.
2. Select an option:
• For most Garmin chartplotters, select
• For other Garmin marine devices, select
3. Select an option:
• To automatically detect the gauge type, select
• To indicate a one-coil gauge, select
• To indicate a two-coil gauge, select
4. Perform the gauge-type setting test.
Configuring the GRA 10 Adapter if the Rudder Angle Calibration and Gauge Type Selections Are Not
Displayed
Depending on the version of software loaded on your Garmin marine instrument, the specific configuration options may not be displayed on the
configuration screens.
To calibrate the rudder angle if the menu option is not displayed:
To use the GRA 10 adapter, you must calibrate the angle of the rudder that the adapter is associated with.
1. Turn the boat ignition key to the On position (not Start).
2. From the NMEA 2000 Devices list, select the GRA 10 device.
3. Select an option:
• For most Garmin chartplotters, select
• For other Garmin marine devices, select
4. Move the rudder fully to starboard and observe the angle of the rudder position, in degrees.
5. Enter the following command: "RUDDERPOS="
26
Review
>
Rudder Angle
Config
>
Rudder Angle
Review
Gauge
Type.
>
Config
>
Gauge
Type.
Auto
Detect.
1
Coil.
2
Coil.
Review
>
Generic
Config.
Config >Generic
Configuration.
Calibration.
Calibration.
Technical Reference for Garmin NMEA 2000 Products