Garmin Alpha 200i Manuale d'uso - Pagina 24
Sfoglia online o scarica il pdf Manuale d'uso per Prodotto per la cura degli animali domestici Garmin Alpha 200i. Garmin Alpha 200i 29. With training
Stampa la pagina
12
Verify the gasket is not damaged and is completely seated in
the groove.
13
Connect the battery connector and the power connector to
the device.
When properly installed, the connector plugs snap into the
ports.
14
Replace the back plate, and replace and tighten the screws
to secure the back plate.
15
Replace the L-shaped cover, and replace and tighten the
screws to secure the L-shaped plate.
16
Verify the gasket is not sticking out of the device.
Replacing the Collar Strap
Before you replace the collar strap, you must remove all dirt,
water, and debris from the device
page
16).
1
Pull the collar strap out of the GPS antenna, antenna guide,
and the dog device.
You may need to push and pull the collar strap to properly
remove it. You may need to loosen the screw on the GPS
antenna case, but do not remove them.
2
Thread the new collar strap through the dog device, antenna
guide, and GPS antenna.
3
If necessary, tighten the screws that secure the GPS antenna
case.
Replacing the VHF Antenna in the Dog Collar Device
Do not excessively bend the band that connects the main device
case with the GPS antenna.
When the L-shaped cover is removed, do not disturb the sealant
opposite the VHF antenna, because this can damage the
waterproof seal of the dog collar device.
Before you replace the VHF antenna, you must remove all dirt,
water, and debris from the device
page
16). Also, you need a small Phillips screwdriver.
1
Remove the 4 screws
VHF antenna.
NOTE: You should note the location of the one short screw.
2
Pry off the L-shaped cover.
20
(Cleaning the Device,
NOTICE
(Cleaning the Device,
from the L-shaped cover over the
3
Remove the screw
securing the VHF antenna to the back
plate.
4
Pull the length of the antenna from the antenna guide to
remove the old antenna.
5
Loop the antenna guide around the collar strap, and thread
the new VHF antenna through the guide.
This helps to point the antenna up.
6
Replace the screw securing the VHF antenna to the back
plate.
7
Replace the L-shaped cover over the VHF antenna.
8
Replace the 4 screws on the L-shaped cover, replacing the
short screw in the correct location.
Changing the Fuse in the Vehicle Power Cable
When replacing the fuse, do not lose any of the small pieces
and make sure they are put back in the proper position. The
vehicle power cable does not work unless it is assembled
correctly.
If your device does not charge in your vehicle, you may need to
replace the fuse located at the tip of the vehicle adapter.
1
Rotate the end piece
TIP: You may need to use a coin to remove the end piece.
2
Remove the end piece, the silver tip
3
Insert a new fast-blow fuse that has the same current, such
as 1 A or 2 A.
4
Place the silver tip in the end piece.
5
Push in the end piece and rotate it clockwise to lock it back
into the vehicle power cable
Data Field Options
24 hr. Max. Temperature: The maximum temperature recorded
in the last 24 hours.
24 hr. Min. Temperature: The minimum temperature recorded
in the last 24 hours.
Accuracy of GPS: The margin of error for your exact location.
For example, your GPS location is accurate to within +/- 12 ft.
(3.65 m).
Alarm Timer: The current time of the countdown timer.
Ambient Pressure: The uncalibrated environmental pressure.
Ascent - Average: The average vertical distance of ascent
since the last reset.
Ascent - Maximum: The maximum rate of ascent in feet per
minute or meters per minute since the last reset.
NOTICE
counter clockwise to unlock it.
, and the fuse
.
.
Appendix