Garmin Astro Istruzioni per la sostituzione

Sfoglia online o scarica il pdf Istruzioni per la sostituzione per Prodotto per la cura degli animali domestici Garmin Astro. Garmin Astro 2. Declaration of conformity
Anche per Garmin Astro: Manuale di avvio rapido (2 pagine), Manuale introduttivo (2 pagine), Istruzioni per la sostituzione (2 pagine), Dichiarazione di conformità (1 pagine), Manuale di istruzioni (9 pagine), Specifiche tecniche (2 pagine)

Garmin Astro Istruzioni per la sostituzione
Battery, Collar, and Antenna Replacement Instructions
This document provides the following instructions.
Replacing the DC 30 Lithium‑ion Battery
Replacing the DC 30 Collar (page 2)
Replacing the VHF Antenna (page 2)
These kits are intended as replacement items for the Garmin
Note: The limited warranty covering this product will not cover any replacement battery, collar, or
antenna not replaced in accordance with these instructions.
Replacing the DC 30 Lithium‑ion Battery
The DC 30 Battery Replacement Kit includes the following parts:
One rechargeable lithium‑ion battery
Two battery‑cover screws (M1.7 × 0.6 × 5 mm)
Four bottom‑cover mounting screws (M2.0 × 0.4 × 8 mm), stainless steel, black oxide
tools required (not included)—one small Phillips screwdriver and a small flat‑blade screwdriver.
Note: It is not necessary to disconnect the DC 30 from the mounting plate on the collar to
replace the battery.
To remove the DC 30 lithium‑ion battery:
1. Use a small Phillips screwdriver to remove the four top‑cover screws from the top cover.
2. Separate the top cover from the bottom cover.
3. Use a small, flat‑blade screwdriver to disconnect the six‑pin connector from the top
cover.
4. Use a small, flat‑blade screwdriver to disconnect the two‑pin connector
from the bottom cover.
5. Use a small Phillips screwdriver to remove the two battery‑cover screws.
6. Remove the battery cover and the battery from the bottom cover.
Note the orientation of the battery in the bottom‑cover housing. You will
install the new battery the same way. Dispose of the old battery according
to local ordinances and regulations.
To replace the DC 30 lithium‑ion battery:
1. Place the replacement battery in the bottom cover. Place the wired end of the
battery on the same end as the Power key on the bottom cover.
2. Attach the battery cover to the bottom cover using the two battery‑cover screws.
3. Connect the replacement‑battery two‑pin connector to the bottom cover.
4. Connect the replacement‑battery six‑pin connector to the top cover by using your thumb to hold the connector against
the housing, as shown in the illustration.
5. Check to ensure proper operation of the replacement battery by pressing the circuit‑board switch. If the red LEDs on
the bottom cover do not begin flashing, check the six‑pin connector for proper connection.
6. Check the charging circuit by connecting the Astro System DC 30 battery charger to an appropriate electrical source
and to the battery‑charging port. If the blue LED is not on, check the two‑pin connector for proper connection.
7. Firmly attach the top cover to the bottom cover using the four top‑cover screws to ensure water resistivity.
8. Fully charge the DC 30 battery before using it as described in the Astro 220 Owner's Manual. Charging a fully
depleted DC 30 battery requires 4½ hours.
August 2008
Astro
System DC 30
Astro
Dog Tracking System.
®
190‑00714‑03 Rev. B
VHF antenna
GPS antenna
Mounting plate
DC 30
Top-cover screws
Battery-cover
screws
Battery cover
Two-pin
connector
Battery
charging
port
DC 30 with Collar
Top cover
Circuit-board
switch
Six-pin
connector
Battery
Bottom cover
Power
key
Six-pin
connector
Printed in Taiwan