Fujitsu Wall Mounted Type Manuale di installazione - Pagina 10
Sfoglia online o scarica il pdf Manuale di installazione per Condizionatore d'aria Fujitsu Wall Mounted Type. Fujitsu Wall Mounted Type 18. Air conditioner outdoor unit, wall mounted type, r410a
Stampa la pagina
] 1 ] 1
8. FINISHING
(1) Insulate between pipes.
● Insulate suction and discharge pipes separately.
● For rear, right, and bottom piping, overlap the connection
pipe heat insulation and indoor unit pipe heat insulation
and bind them with vinyl tape so that there is no gap.
● For left and left rear piping, butt the connection pipe heat
insulation and indoor unit pipe heat insulation together and
bind them with and vinyl tape so that there is no gap.
● For left and left rear piping, wrap the area which
accommodates the rear piping housing section with cloth tape.
● For left and left rear piping, bind the connection cable to
the top of the pipe with vinyl tape.
● For left and left rear piping, bundle the piping and drain hose
together by wrapping them with cloth tape over the range
within which they fi t into the rear piping housing section.
(2) Temporarily fasten the connection cable along the
connection pipe with vinyl tape. (Wrap to about 1/3 the
width of the tape from the bottom of the pipe so that
water does not enter.)
(3) Fasten the connection pipe to the outside wall with
saddles, etc.
(4) Fill the gap between the outside wall pipe hole and the pipe
with sealer so that rain water and wind cannot blow in.
(5) Fasten the drain hose to the outside wall, etc.
Saddle*
Pipe
Overlap the insulation
Connection pipe
(heat insulation)
Bind the pipes together so
that there is no gap.
Pipe
Cloth tape
Drain hose
Left piping
Connection cable
Pipe
For connection from the left rear
Wall pipe
Drain hose
Check the following:
Drain hose
GOOD
Saddle
En-10
Outside wall cap*
Sealer putty*
(Outdoors)
Wall
*Field supplied
Indoor unit pipe
(heat insulation)
Vinyl tape
Wrap with
cloth tape
Drain hose
Connection cable
Connection pipe
NO GOOD NO GOOD NO GOOD
Lifted up
Wave
End in water
] 1
9. FRONT PANEL REMOVAL AND INSTALLATION
9.1. Intake grille removal
(1) Open the intake grille.
(2) Pull down the knob.
(3) Lift the intake grille upward, until the axle at the top of the
intake grille is removed.
1
9.2. Intake grille installation
(1) The fi xing axle of the intake grille is installed on the Panel.
(2) Lay down the intake grille.
1
9.3. Front panel removal
(1) Remove intake grille (Reference the intake grille removal.)
(2) Remove 6 screws.
(3) The thumb is hung on the lower part as shown in the fi gure,
and it pulls to the front, pushing [▲] mark , and bottom
hooks (2 position) is removed from wall hook bracket.
(4) The front panel is pulled to the front, raising the upper
surface, and a front panel is removed.
9.4. Front panel installation
(1) First, fi t the lower part of the front panel, and insert top
and bottom hooks. (3 top sides)
(2) Attach the 6 screws.
(3) Attach the intake grille.
Intake grille
Mounting shaft
Bearing
Front panel
Screws (6 position)
Front panel
Wall hook bracket
Push
[▲] mark
Push
Top holes (two sides)
Top hole (center)
Indoor unit
CAUTION
Install the front panel and INTAKE GRILLE securely.
If installation is imperfect, the front panel or INTAKE
GRILLE may fall off and cause injury.
Intake grille
Knob
Front panel
Top hook (center)
Front panel
Top hooks
(2 sides)