Brother PT-1160 Martha By Mail Manuale d'uso

Sfoglia online o scarica il pdf Manuale d'uso per Etichettatrice Brother PT-1160 Martha By Mail. Brother PT-1160 Martha By Mail 2. Brother pt-1160: users manual
Anche per Brother PT-1160 Martha By Mail: Manuale di servizio (9 pagine)

Stampa la pagina

SKU HPT003

PT-1160

USER'S GUIDE

LA6618001

Printed in China

GENERAL PRECAUTIONS

•

Use only Brother TZ tapes with this machine. Do not use any other tapes.

•

Tapes are available in three different widths: 1/4"(6 mm), 3/8"(9 mm) and 1/2"(12 mm).

•

Do not pull the tape since this may damage the tape cassette.

•

Do not attempt to cut the tape while printing or feeding since this will damage the

tape.

•

Do not clean the machine with alcohol or other organic solvents. Use only a soft, dry

cloth.

•

Remove the batteries and disconnect the AC adapter if you do not intend to use the

machine for an extended period of time.

Note: If power is disconnected for more than three minutes, all text shown in the

display and any text files stored in the memory will be lost.

•

Do not put any foreign objects into or anything on the machine.

•

Do not expose the machine to high temperatures or high humidity. Never leave it on

the dashboard or in the back of your car.

•

Do not use the machine in dusty places, and keep it out of both direct sunlight and

rain.

•

Do not leave any rubber or vinyl on the machine for an extended period of time.

Doing so may cause staining.

•

After inserting a new tape cassette, advance the tape by holding down

pressing

once.

•

Do not touch the print head mechanism. If the head is touched, clean it immediately

with a soft wipe (e.g., a cotton swab) to avoid permanent damage.

•

To avoid injuries, do not touch the cutter's edge.

•

Use only the AC adapter designed exclusively for this machine. Use of any

other adapter will void the warranty.

Please contact your Brother dealer for details.

POWER SUPPLY

Changing the batteries

CAUTION

Batteries installed incorrectly can overheat and leak. Can result in chemical burns

and machine overheating and damage.

Your machine requires 6 alkaline AAA batteries.

Carefully follow these instructions.

1 Press bumps on top of back cover and open.

2 Pull out tape cassette, if one was installed.

3 Remove batteries, if they were already installed.

4 Hold machine as pictured:

FIRST, in

5 Insert six new batteries as follows:

LOWER

layer

Always:

insert ˝+˝ ends

pointing DOWN.

• Insert "+" ends before "-" ends.

• Remove "-" ends before "+" ends.

• Replace all 6 batteries at the same time with new ones.

6 Insert tape cassette.

7 Insert two hooks on bottom end of back cover into slots on bottom

of machine. Push down firmly on cover until it snaps into place.

8 Turn machine on.

If no power, immediately remove batteries and call Brother Customer Service at:

1-877-478-6824

Optional AC adapter

The AC adapter allows you to use this machine wherever an electrical outlet is available.

Use Brother's AD-30 adapter for your new PT-1160.

1 Insert the plug on the adapter cord into the adapter

jack on the bottom end of the machine.

2 Insert the plug into the nearest standard electrical outlet.

OVERVIEW

Tape cutter lever

Display

Backspace key

Return key

Function dial

Back cover

Caps key

Num key

On/Off key

Batteries

Tape cassette

TAPE CASSETTES

A TZ tape cassette is supplied with this unit. The Brother TZ tapes used with this machine are

available in a variety of colors and three tape widths (1/4"(6 mm), 3/8"(9 mm), 1/2"(12 mm)).

1 Press in on the rough area at the top end of the machine and

fold open the back cover.

2 If a tape cassette is already installed, remove it by pulling it

straight up.

3 If the ink ribbon in the other tape cassette is loose, use your

finger to wind the toothed wheel in the direction of the arrow on

the cassette until there is no slack in the ribbon. Also, make sure

that the end of the tape feeds under the tape guides.

Note: If you are using a new tape cassette provided with a

stopper, be sure to remove the stopper.

4 Insert the tape cassette firmly into the compartment, making

sure that the entire back of the cassette contacts the bottom of

the compartment.

Note: When inserting a tape cassette, make sure that the inner

ribbon does not catch on the corner of the metal guide.

5 Securely close the back cover, making sure that it snaps into place.

and

6 Feed the tape by holding down

and pressing

then push in the tape cutter lever to cut the tape.

LETTERING STICK

The enclosed lettering stick enables you to easily remove the backing from labels printed

on laminated tapes.

1 Hold the tape in your left hand, with the printed surface facing up, and hold the stick

in your right hand.

2 Pass the tape halfway through the long narrow hole in the stick.

3 Turn the stick three-quarters of a turn towards you and pull the stick away from you

as shown below.

4 Peel off the label backing.

STARTING

Press

. If batteries have been installed or the machine has been plugged in using the

optional AC adapter, the previous session's information is displayed when the machine is

SECOND, in

UPPER

layer

turned on. This feature allows you to stop work on a label and turn off the machine, then

insert ˝+˝ ends

return to it later without having to re-enter the text.

pointing UP.

The machine automatically turns off if no key is pressed within five minutes. The current

session's information is stored in the machine's internal memory and displayed when the

machine is later turned on again.

CODE KEY

By holding down

and pressing a key with a function, character or accent written

above it, you can use the corresponding function or add the corresponding character to

your text.

CAPS KEY

By pressing

to enter Caps mode, you can add upper-case letters to your text by

simply pressing the character keys. When this mode is on, the Caps indicator in the top-

left corner of the display comes on. To exit Caps mode, press

indicator goes off.

NUM KEY

By pressing

to enter Num mode, you can add numbers to your text by simply

pressing the corresponding keys. When this mode is on, the Num indicator in the bottom-

left corner of the display comes on. To exit Num mode, press

goes off.

DISPLAY

This machine's LCD shows one row of 8 characters; however, the text that you enter can

be up to 55 characters in length. The 8-character display is like a window which moves

across the text.

Print head

1234567890123456789012345678901234567890123456789012345

Tape exit slot

CURSOR MOVEMENT

You can view and edit different parts of the text by moving the cursor backward and

forward.

To move the cursor one character at a time, press

To move the cursor to the beginning of the text, hold down

To move the cursor to the end of the text, hold down

BACKSPACE KEY

This key can be used to remove characters from your text, clear all of the text or cancel

functions.

To delete the character to the left of the cursor or to cancel a function (instead of

pressing

), press

To clear all of the text that is currently entered, hold down

SPACE KEY

once, and

As on a word processor, press

RETURN KEY

Press

when you wish to select a setting, or end the first line of text and start the

second.

To add a second line, press

indicate the end of the first line and the beginning of the second.

Note: Two lines of text can only be entered if 3/8"(9-mm) or 1/2"(12-mm)-wide tape

is installed.

To select an item from a list, press

ACCENTED CHARACTERS

You can also choose from a list of other accented characters that can be added to your text.

Letter

Accented character

1 Press

if you want the accented character to be an upper case letter.

Note: To quit the following procedure at any time without making any changes, press

2 Hold down

and press

. The message "A-U?" appears in the display.

3 Turn the Function dial until the cursor is positioned under the desired accented

character.

Press the key for the letter in the accented character that you wish to add, and then

press

and

until the cursor is positioned under the desired accented

character.

4 Press the Function dial (or

) to add the selected character to your text.

until the Caps

SYMBOLS

In addition to the letters, symbols, and numerals on and above the keys, there are 72

symbols available with the Symbol function. These symbols are divided into 10 groups,

corresponding to the letters A through I.

until the Num indicator

Group

←

→

1 Press

. The message "A-I?" appears in the display.

2 Press the key for the letter of the group containing the symbol that you wish to add,

and then press

and

until the cursor is positioned under the desired symbol.

3 Press

to add the symbol to the text.

and press

to add a blank space to your text.

once. The return mark ( ) appears in the text to

once.

Letter

Accented character

Symbols

;

[

]

↑

↓