Fujitsu ScanSnap iScanner fi-6010N Manuale introduttivo - Pagina 5
Sfoglia online o scarica il pdf Manuale introduttivo per Scanner Fujitsu ScanSnap iScanner fi-6010N. Fujitsu ScanSnap iScanner fi-6010N 21. Network adf scanner
Anche per Fujitsu ScanSnap iScanner fi-6010N: Specifiche tecniche (2 pagine), Opuscolo e specifiche (2 pagine), Manuale introduttivo (21 pagine), Manuale introduttivo (45 pagine), Istruzioni per la pulizia (2 pagine), Istruzioni per la pulizia (2 pagine)
Stampa la pagina
Do not touch the inside of the scanner
unless necessary.
Do not take apart or modify the scanner.
The inside of the scanner contains high-
voltage components. Touching these
components might cause electric shock or
fire.
Do not use the scanner if you smell a
strange odor.
If you detect heat coming from the device or
detect other problems such as smoke,
strange smells or noises, immediately turn
off the scanner and then disconnect its
power plug. Make sure that any smoke
coming from it has stopped, before
contacting your FUJITSU scanner dealer or
an authorized FUJITSU scanner service
provider.
Do not use aerosol sprays near the
scanner.
Do not use any aerosol sprays or alcohol
based sprays to clean the scanner.
Dust blown up by strong air from the spray
may enter the inside of the scanner. This
may cause the scanner to fail or
malfunction.
Sparks, caused by static electricity,
generated when blowing off dust and dirt
from the outside of the scanner may cause
a fire.
Do not place the scanner within the reach
of small children.
To avoid injuries, do not place the scanner
in an area where small children may be able
to reach.
Do not touch the heated section for a long
time.
Do not touch the heated section such as the
bottom of the scanner for a long time.
Doing so may cause a low-temperature
burn on your skin.
Do not cover the scanner with something
during its operation.
Do not use the scanner while covered with a
blanket, etc. Doing so may raise the
temperature inside and cause a fire.
Do not use the scanner where it gets wet.
Do not use the scanner at a place such as a
bathroom, shower room, or swimming pool
where it may easily get wet. Doing so might
cause electric shock or fire.
AUTION
Do not install the scanner on unstable
surfaces.
Make sure that the scanner is installed on a
flat, level surface and that none of its parts
extend beyond the surface top, such as a
desk or table. Do not install the scanner on
unstable surfaces. Install the scanner on a
level surface that is free of vibration to
prevent it from falling.
Install the scanner on a strong surface that
will support the weight of the scanner and
other devices.
Do not block the ventilation ports.
Do not block the ventilation ports. Blocking
the ventilation ports generates heat inside
of scanner, which may result in fire or
scanner failure.
Do not place heavy objects or climb on
top of the scanner.
Do not place heavy objects on the scanner
or use the scanner's surface top to perform
other work. Improper installation might
cause injuries and equipment failure.
Firmly insert the power plug.
Firmly insert the power plug as far it can go
into the power outlet.
vii
Avoid any contact when scanner is in use.
Avoid touching any scanner mechanism
during scanning since this may cause
injuries.
Do not use the scanner immediately after
moving it from a cold place into a warm
room.
Do not use the device immediately after
moving it from a cold place into a warm
room. Condensation may occur, which
might lead to scanning errors. Let the
device dry about one or two hours before
you use it.
Before moving the scanner, disconnect
the power plug from the power outlet.
Do not move the scanner with the power
and interface cables connected as this can
damage the cables, which can later cause
fire, electric shock as well as injury.
Before moving the scanner, be sure to
disconnect the power plug from the power
outlet, and all other data cables.
Make sure that the floor is free of any
obstructions.
Protect the scanner from static electricity.
Install the scanner away from strong
magnetic fields and other sources of
electronic noise. Also, protect the scanner
against any static electricity, which can
cause the scanner to malfunction.
Disconnect the power plug from the
power outlet when the scanner is not used
for a long period of time.
When the scanner is not going to be used
for a long period of time, be sure to
disconnect the power plug from the power
outlet for safety.
Do not install the scanner in the direct
sunlight.
Do not install the scanner under direct
sunlight or near heating apparatus. Doing
so might cause excessive heat to build up
inside the scanner, which can cause
scanner trouble or even fire. Install the
scanner in a well-ventilated location.
fi-6010N Network Scanner Getting Started
Handle documents carefully.
When handling documents, be careful not to
cut your fingers with them.
Do not make the scanner wet while
carrying it outside.
When carrying the scanner outside while it
is raining or snowing, pay special attention
so the scanner does not get wet.
Do not place the scanner in areas, which
are subject to high levels of shock or
vibration.
Do not place the scanner in areas, which
are subject to high levels of shock or
vibration. Doing so may cause the scanner
to malfunction.
viii