Indesit D2I HL326 Manuale di riferimento giornaliero - Pagina 7
Sfoglia online o scarica il pdf Manuale di riferimento giornaliero per Lavastoviglie Indesit D2I HL326. Indesit D2I HL326 8.
Stampa la pagina
TROUBLESHOOTING
In case your dishwasher doesn't work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.
The manufacturer ensures the availability of spare parts for at least 10 years after production date of this appliance.
PROBLEMS
POSSIBLE CAUSES
Salt reservoir is empty.
Salt indicator
(After refill the salt indicator may remain lit
is lit
for several wash cycles).
The appliance has not been plugged in
The dishwasher
won't start
properly.
or does not
Power outage.
respond to com-
mands.
The dishwasher door is not closed.
Cycle is interupted by door opening for
more than 4 seconds.
It does not respond to commands.
The wash cycle has not finished yet.
The dishwasher
won't drain.
The drain hose is bent.
The sink drain pipe is blocked.
The filter is clogged up with food residues.
The dishwasher
The dishes are rattling against each other.
makes
excessive noise.
An excessive amount of foam has been
produced.
The crockery has not been arranged
The dishes are
properly.
not clean.
The spray arms cannot rotate freely, being
hindered by the dishes.
The wash cycle is too gentle.
An excessive amount of foam has been
produced.
The cap on the rinse aid compartment has
not been shut correctly.
The filter is soiled or clogged.
There is no salt.
No water in the water supply or the tap is
The dishwasher
closed.
does not fill the
water.
The inlet hose is bent.
All LEDs are
The sieve in the water inlet hose is clogged;
blinking rapidly
it is necessary to clean it
Dishwasher
Drain hose positioned too low or siphoning
finishes the cycle
into home sewage system.
prematurely.
Air in water supply.
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
• Visiting our website: docs.indesit.eu
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product's
identification plate.
SOLUTIONS
Refill reservoir with salt (for more information - see page 2).
Adjust water hardness - see table, page 2.
Insert the plug into the socket.
For safety reasons, dishwasher will not re-start automatically when power returns.
Open dishwasher door, press Start button and close the door within 4 seconds.
Vigorously push the door until you hear the "click".
Press START/Pause and close the door within 4 seconds.
Switch off the appliance by pressing the ON/OFF button, switch it back on
after approximately one minute and restart the program. If problem persists,
unplug the appliance for 1 minute, then plug it back in.
Wait until the wash cycle finishes.
Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
Clean the sink drain pipe.
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
Position the crockery correctly (see LOADING THE RACKS).
The detergent has not been measured out correctly or it is not suitable for
use in dishwashers (see FILLING THE DETERGENT DISPENSER). Restart the cur-
rent cycle by switching OFF the dishwasher, then switch it on again, select a
new program, press START/Pause and close the door within 4 seconds. Please
do not add any detergent.
Arrange the crockery correctly (see LOADING THE RACKS).
Arrange the crockery correctly (see LOADING THE RACKS).
Select an appropriate wash cycle (see PROGRAMS TABLE).
The detergent has not been measured out correctly or it is not suitable for use
in dishwashers (see FILLING THE DETERGENT DISPENSER).
Make sure the cap of the rinse aid dispenser is closed.
Clean the filter assembly (see CARE AND MAINTENANCE).
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
Make sure there is water in the water supply or the tap running.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dish-
washer and reboot.
After having carried out the verification and cleaning, turn off and turn on the
dishwasher and restart a new program.
Check if end of drain hose is placed at correct height (see INSTALLATION).
Check for siphoning into home sewage system, install air admittance valve if
necessary.
Check water supply for leaks or other issues letting air inside.
EN
IEC 436
:
7