Indesit KN6G527S/RU S Manuale di istruzioni per l'uso - Pagina 21

Sfoglia online o scarica il pdf Manuale di istruzioni per l'uso per Fornelli Indesit KN6G527S/RU S. Indesit KN6G527S/RU S 32.

Indesit KN6G527S/RU S Manuale di istruzioni per l'uso
! If one or more of these conditions is not fulfilled or
if the cooker must be installed according to the
conditions listed for class 2 - subclass 1 appliances
(installed between two cupboards), the flexible steel
hose must be used instead ( see below ).
Connecting a flexible jointless stainless steel pipe
to a threaded attachment
Make sure that the hose and gaskets comply with
current national legislation.
To begin using the hose, remove the hose holder on the
appliance (the gas supply inlet on the appliance is a
cylindrical threaded 1/2 gas male attachment).
! Perform the connection in such a way that the hose
length does not exceed a maximum of 2 metres,
making sure that the hose is not compressed and
does not come into contact with moving parts.
Checking the connection for leaks
When the installation process is complete, check
the hose fittings for leaks using a soapy solution.
Never use a flame.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas
other than the default type (this is indicated on the
rating label on the cover).
Adapting the hob
Replacing the nozzles for the hob burners:
1. Remove the hob grids and slide the burners off
their seats.
2. Unscrew the nozzles using a
7 mm socket spanner ( see
figure ), and replace them with
nozzles suited to the new type
of gas( see Burner and nozzle
specifications table ).
3. Replace all the components
by following the above
instructions in reverse.
Adjusting the hob burners' minimum setting:
1. Turn the tap to the minimum position.
2. Remove the knob and adjust the regulatory
screw, which is positioned inside or next to the tap
pin, until the flame is small but steady.
! If the appliance is connected to a liquid gas
supply, the regulatory screw must be fastened as
tightly as possible.
3. While the burner is alight, quickly change the position
of the knob from minimum to maximum and vice versa
several times, checking that the flame is not
extinguished.
! The hob burners do not require primary air adjustment.
We recommend cleaning the oven before using it for
the first time, following the instructions provided in
the "Care and maintenance" section.

TECHNICAL DATA

Oven dimensions
32x40x43,5 cm
(HxWxD)
Volume
57 l
Useful
width 42 cm
measurements
depth 46 cm
relating to the oven
height 8,5 cm
compartment
Power supply voltage
see data plate
and frequency
Declared energy consumption for
Natural convection Class
Heating mode:
Energy Label
Energy consumption for Forced
convection heating mode:
may be adapted for use with any
type of gas shown on the data
plate, which is located inside the
Burners
flap or, after the oven
compartment has been opened,
on the left-hand wall inside the
oven.
EC Directives: 2006/95/EC dated
12/12/06 (Low Voltage) and
subsequent amendments -
2004/108/EC dated 15/12/04
(Electromagnetic Compatibility)
and subsequent amendments -
2009/142/EC dated 30/11/09
(Gas) and subsequent
amendments - 93/68/EEC dated
22/07/93 and subsequent
amendments - 2002/96/EC.
1275/2008 (Stand-by/ Off mode)
Data plate, is located inside the flap or, after the
ovencompartment has been opened, on the left-hand
wall inside the oven.
GB
Convection
Fan assisted
21