Acadalus CPS-h1 Manuale d'uso - Pagina 4

Sfoglia online o scarica il pdf Manuale d'uso per Camera Accessories Acadalus CPS-h1. Acadalus CPS-h1 7. Self-leveling camera head

Stampa la pagina

OPERATING INSTRUCTIONS

Checking the charge of the

battery pack

Push the fuel gauge button to activate

the battery's power level display. Each

of the five lights indicate approximately

1/5 of the entire charge. It takes the age,

temperature and the actual charge of the

battery into account to indicate an esti-

mated charge level. The remaining charge

indicator may not be correct under certain

circumstances.

Note:

Battery capacity decreases over time and

through repeated use. When the operating

time per charge decreases markedly, the

battery pack should be replaced.

Charging the battery pack

Disconnect the battery pack from the

Acadalus CPS H1 Camera Head.

Connect the charger to the mains us-

ing the charger power cord.

Charge the battery until the charger

LED turns from red to green.

Disconnect the charger.

Attaching the battery pack to

the CPS H1 Camera Head

Slide the battery with the connector

into the left accessory shoe on the CPS

H1 Camera Head.

Connect the Multipur-

pose Cable to one of the

20-pin sockets on the

battery pack

and plug it

into a 20-pin

socket on the

head.

A second battery can be

attached to the empty socket of the CPS H1

Camera Head. Additional batteries can be

attached to any free sockets of the system

including those of battery packs.

Connecting the AC Adaptor to

the CPS H1 Camera Head

Connect the Power Supply to the mains

with the AC Adaptor power cord.

Connect the DC power plug of the

charger to the DC in socket on the bot-

tom of the CPS H1 Camera Head.

Note:

The power supply does not recharge

connected batteries. For your safety the

batteries are electrically separated from the

AC Adaptor which is does not contain the

circuitry to safely recharge Li-ion batteries.

Caution:

Using power supplies other than those

supplied by Koch Photography could lead

to malfunction or destruction of the device.

Using the Acadalus CPS H1

camera head abroad

You can use the Acadalus CPS H1 camera

head, the battery charger, and the AC

Adaptor in any country or region where

the power supply is within 100 V to 240 V

AC, 50/60Hz.

Do not use an electronic transformer (trav-

el converter). This may cause a malfunction.

Attaching the CPS H1 Camera

Head to the tripod or camera

stand

If necessary, attach or remove the 3/8"

¼" reducing bushing to obtain the ap-

propriate tripod mount.

Move the locking lever to the left side.

Use the tripod bolt to mount the head.

Only tighten the tripod screw lightly.

Now firmly secure the head to the

tripod by moving the locking lever to

the right.

Securing a device on top of the

CPS H1 Camera Head

If necessary,

re-position

the 3/8" – 1/4"

Camera Adapt-

er Screw so the

appropriate

thread for the device to be mounted is

accessible.

After setting the appropriate height of

the stud, secure the 3/8" – 1/4" Camera

Adapter Screw gently with the sup-

plied 3/8" jam nut to the turntable.

Mount the camera or other accessory

to the platform.

Initializing the rotational

position of the CPS H1 Camera

Head

Point the camera lens away from the

control panel and secure the platform

with the rotation locking knob.

Turn on the head by pushing the "On"

button.

The system starts up. While booting and

performing a self-test, the LEDs on the

arrow keys light up clockwise. As soon as

this display stops, the hardware has passed

all tests and is ready. The CPS H1 Camera

Head requires the lens to point forward at

start-up to compute natural movements

when the inclination of the head is manu-

ally adjusted.