Kohler 77632T Istruzioni per l'installazione - Pagina 2
Sfoglia online o scarica il pdf Istruzioni per l'installazione per Apparecchiature per il bagno Kohler 77632T. Kohler 77632T 2. Straight shower column with showerhead; curved shower column with showerhead
Stampa la paginaINSTALLATION
How to Install the Shower Column
Select a location in vertical wall to install shower column according to
rough-in dimensions.
Drill the lower hole as anchors(1) diameter and lower base(3-1) position
in the finished wall(NOTE: The arrow in the base is upward). Press
anchors into the hole, secure the base by the screw(2).
Rehearse the slide bar kit(4) installation for the upper base(3-2) mounting
location determination. Slide the tube joint(5) onto the slide bar kit, and
connect them to the base(NOTE: The arrow in the base is upward).
Install the screws(7) into the tube joint with the hex wrench(6), and
tighten them.
Place the slide bar and the body against the finished wall. Connect the
lower base and the diverter body kit(8). Position and tighten them by hex
wrench. Mark the hole of upper base(3-2) with a pencil. Uninstall the slide
bar kit and tube joint.(NOTE: Don't lose the screws.)
Drill holes on the mark. Press the anchors into the holes. Secure the
upper base(3-2) by the screws. Install the tube joint(5) to the base(3-2)
and tighten them by screws. Reinstall the slide bar kit with escutcheons
(9) to the bases. Tighten the screws with the hex wrench. Screw the
escutcheons with the bases until against the finished wall.
Install the tube kit(10) into the slide bar kit. Install the nut(11) onto the
tube kit with soft cloth between internal hole of the nut and the tube kit.
Then screw the nut onto the slide bar kit with strap wrench or soft cloth
between the nut and regular wrench.
Connect the hose(12) between the mixer water supply and the
connector(13). The connector(14) will be used for handspray connection.
How to Install the Showerhead
Turn the diverter handle to showerhead(18) work, run hot and cold water
for about one minute to remove any debris before the showerhead is
installed.
Before installation, put the regulator(17) into the showerhead inlet if
needed. Take out the washer(16) and install the regulator as shown,
reinstall the washer. Tighten the showerhead onto the tube kit outlet(15)
with strap wrench.
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc. which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
1265604-2A-B
10
1
3-2
11
2
7
5
9
4
6
7
9
1
3-1
2
8
13
14
12
15
16
17
18
2
SERVICE PARTS
12966T-C
12969T-C
77632T
12967T-C
12966T-C/12969T-C
/77632T:1121294**
12967T-C:1121282**
1196610
870992
1196622**
1196609**
1121285
1061576
1196621**
832751
1268608**
1256397**
1109471**
12966T-C/12969T-C/77632T:1196627**
12967T-C:1222095**
1256401**
832751
1196610
1196628
1196607**
870921
1061576
1183267**
1196621**
832751
870921
**Color code must be specified when ordering
1265604-2A-B
Straight Shower Column With Showerhead
Curved Shower Column With Showerhead
77420
1030624
12966T-C-CP:1260902**
77420
1030624
12966T-C-RGD:1261848**
77420
1030624
12967T/12969T-C-CP:
1260903**
77420
1030624
12967T-C-2BZ/AF/BN/RGD
&12969T-C-AF/BN/RGD:
1250134**
77420
1030624
77632T-**:1260904**
1154793**
3