Kohler Command PRO CH620 Manuale d'uso - Pagina 7

Sfoglia online o scarica il pdf Manuale d'uso per Motore Kohler Command PRO CH620. Kohler Command PRO CH620 10. Vertical/horizontal crankshaft
Anche per Kohler Command PRO CH620: Manuale d'uso (21 pagine), Manuale d'uso (8 pagine), Manuale d'uso (24 pagine), Manuale d'uso (8 pagine)

Stampa la pagina

Spark Plugs

AcAUTION

Electrical Shock can cause injury.

Do not touch wires while engine

is runhing.

< 3an out spark plug recess. Remove plug and

replace.

Check gap using wire feeler gauge. Adjust

gap, see specification table for adjustment.

2. lnstall plug ir:ifö cylinder head.

forque plug to

ft. lb.

(27

N·m).

Cleaner

1\ ITE: Operating engine with loose or

damaged air cleaner components

could cause premature wear and

failure. Replace all bent or damaged

components.

IIOTE: Paper element cannot be blown out

with compressed air.

.ow-Profile/Commercial Mower

. r 1sen knob and remove air cleaner cover.

~l -

cleaner:

. Remove precleaner from paper element.

leplace or wash precleaner in warm water

with detergent. Rinse and allow to air dry.

:. '";aturate precleaner with new engine oil;

queeze out excess oil.

•· Reinstall precleaner over paper element.

,er Element:

. ..;1ean area around element. Remove wing

nut, element cover, and paper element with

recleaner.

. ,:,eparate precleaner from element; service

precleaner and replace paper element.

. :heck condition of rubber seal' and replace if

, ,ecessary.

• 1

'1stall new paper element on base; install

redeaner over paper element; reinstall

vlement cover and secure with wing nut.

eiristall air cleaner cover and secure with

1 ).

eavy-Duty

· · nhook retaining clips and remove end

lp(s).

Check and clean inlet screen (if equipped).

~II air cleaner element out of housing and

. .1place. Check condition of inner element;

replace when dirty.

4. Check all parts for wear, cracks, or damage,

and that ejector area is clean.

5. lnstall new element(s).

6. Reinstall end cap(s) with dust ejector valve/

screen down; secure with retaining clips. _

Br eather Tube

Ensure both ends of breather tube are properly

connected.

011 Cooler (1f equ1pped)

Clean fins with a brush or compressed air.

2. Remove two screws securing oil cooler, and

tilt to clean back side.

Reinstall oil cooler.

Arr Cool111g

AwARNING

Hot Parts can cause severe

bums.

Do not touch engine while

operating or just after stopping .

Never operate engine with heat shields or

guards temqved .

Proper cooling is essential. To prevent over

heating, clean screens, cooling fins, and other

external surfaces of engine. Avoid spraying

water at wiring harness or any electrical -

components. See Maintenance Schedule.

Repa1rs/Service Parts

We recommend !hat you use a Koh(er

authorized dealer for all maintenance,

service, and replacement parts for engine.

To find a Kohler authorized dealer visit

KohlerEngines.com or call

1-800-544-2444

(U.S. and Canada) .

Storage

lf engine will be out of service for 2 months or

more follow procedure below .

Add Kohler PRO Series fuel treatment or

equivalent to fuel tank. Run engine

2-3

minutes to get stabilized fuel into fuel system

(failures due to untreated fuel are not

warrantable ).

2. Change oil while engine is still warm from

operation. Remove spark plug(s) and pour

about 1 oz. of engine oil into cylinder(s).

Replace spark plug(s) and crank engine

slowly to distribute oil.

Disconnect negative(-) battery cable .

4. Store engine in a clean, dry place.

,90 31 Rev C

KohlP.rl=nnin,::ac::

r-nm